Operation; Transport; Storage; Care And Service - Kärcher NT 65/2 Ap Originalbetriebsanleitung

Dry vacuuming
 An additional paper filter bag can be used when vac-
uuming fine dust.
Installing the paper filter bag
1. Unlock and remove the suction head.
2. Connect the paper filter bag.
Illustration C
3. Fit and lock the suction head.
Wet vacuum cleaning
Note
The flat fold filter (cellulose) with the order number
6.904-283.0 included in the scope of delivery is not rec-
ommended for regular wet vacuum cleaning.
Installing the squeegees
1. Remove the brush strip.
Illustration D
2. Install the squeegees.
Removing the paper filter bag
 The paper filter bag must always be removed when
vacuuming wet substances.
 It is recommended to use a special filter bag (wet)
(see filter systems).
Draining the waste water
WARNING
Improper disposal of waste water
Environmental pollution
Observe the local waste water treatment regulations.
1. Drain the waste water via the drain hose.
Device with a metal container:
Illustration E
Device with a plastic container:
Illustration F
Draining the container completely
NT 75/2 only:
1. Lock parking brake.
2. Hold the container by the handle and tilt it by lifting.
Illustration G
3. Completely drain the container.
4. Tilt the container back into its original position.
5. Release the parking brake.
General
 We recommend not using the "Semi-automatic filter
dedusting" function button when vacuuming wet dirt
with the crevice nozzle or upholstery nozzle (option-
al) when sucking mainly water out of a container.
 The device switches off automatically when the
maximum fluid level is reached.
 When vacuuming non-conductive liquids (e.g. drill
emulsion, oils and grease) the device does not au-
tomatically switch off when the container is full. The
filling level must be continuously monitored and the
container emptied on a timely basis.
 On completion of wet vacuum cleaning: Clean the
flat fold filter using the dedusting function. Clean the
electrodes with a brush. Clean the container with a
moist cloth and dry it off.
Clip connection
The suction hose is equipped with a clip system. All ac-
cessory parts with a nominal width of 40 mm can be
connected.
Illustration H
Switching on the device
1. Connect the mains plug.
2. Switch on the device at the main switch.
Semi-automatic filter dedusting
Note
Actuating the semi-automatic filter dedusting every 5-10
minutes extends the working time of the flat fold filter.
Note
The semi-automatic filter dedusting can only be
switched on when the device is switched on.
1. Press the semi-automatic filter dedusting button 5x.
The flat fold filter is then cleaned by a blast of air
(pulsing noise).
Switching off the device
1. Press the semi-automatic filter dedusting button 5x.
2. Switch off the device at the main switch.
3. Pull out the mains plug.
Each time after use
1. Empty the container.
2. Vacuum off the inside and outside of the device and
clean with a moist cloth.
Storing the device
1. Store the suction hose and mains cable as shown in
the illustration.
Illustration I
2. Store the device in a dry room and secure it against
unauthorised use.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
1. Remove the suction hose with floor nozzle from the
support. Carry the device by the carrying handle and
suction pipe.
2. Load the device by the chassis handle or steering
roller bracket and push handle.
3. Pull the device behind you via the push handle for
transporting over longer distances.
4. When transporting the device in vehicles, secure it
to prevent it from slipping or overturning in accord-
ance with the respective valid guidelines.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
The device may only be operated indoors.

Care and service

DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the mains plug.
English

Operation

Transport

Storage

11