Specifications; Specific Safety Rules - Makita 6261D Bedienungsanleitung

ENGLISH
1-1. Button
1-2. Battery cartridge
2-1. Switch trigger
3-1. Reversing switch lever

SPECIFICATIONS

Model
Capacities
-1
No load speed (min )
Overall length
Net weight
Rated voltage
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for drilling and screw driving in wood,
metal and plastic.
For Model 6261D,6271D,6281D,6381D,6391D
Noise
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745-2-1:
Sound pressure level (L
The noise level under working may exceed 85 dB(A)
Wear ear protection
Vibration
The vibration total
determined according to EN60745-2-1:
Work mode: Drilling into metal
Vibration emission (a
EC-DECLARATION OF CONFORMITY
Model; 6261D,6271D,6281D,6381D,6391D
We declare under our sole responsibility that this
product is in compliance with the following standards of
standardized documents;
EN60745, EN55014
Directives, 2004/108/EC, 98/37/EC.
000230
Tomoyasu Kato
Explanation of general view
4-1. Low speed
4-2. High speed
4-3. Speed change lever
5-1. Graduations
Steel
Wood
Wood screw 5.1 mm x 38 mm
Machine screw
High
Low
) : 70 dB(A) or less
pA
value (tri-axial vector
2
) : 2.5 m/s or less
h,D
in accordance with Council
CE2007
6261D 6271D
10 mm 10 mm
21 mm 25 mm
192 mm
1.4 kg 1.5 kg
D.C. 9.6 V D.C. 12 V
ENE034-1
Responsible Manufacturer:
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
ENG103-1
8JD, ENGLAND

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to drill safety rules. If you use this power tool
unsafely or incorrectly, you can suffer serious
personal injury.
ENG202-1
1. Hold power tools by insulated gripping
surfaces when performing an operation where
sum)
the cutting tool may contact hidden wiring or
its own cord. Contact with a "live" wire will make
exposed metal parts of the tool "live" and shock
the operator.
ENH102-7
2. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not leave the tool running. Operate the tool
only when hand-held.
6. Do not touch the drill bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
7. Some material contains chemicals which may
be toxic. Take caution to prevent dust
3
5-2. Adjusting ring
5-3. Drill marking
5-4. Pointer
6-1. Sleeve
6281D 6381D
10 mm 13 mm
25 mm 25 mm
5.1 mm x 63 mm
6 mm
0 - 1,300
0 - 400
200 mm
1.6 kg 1.6 kg
D.C. 14.4 V D.C. 14.4 V
Director
6391D
13 mm
36 mm
6 mm x 75 mm
216 mm
2.2 kg
D.C.18V
GEB002-2