Werbung
© BOSTITCH 2019
3. Open the jam clearing nose door by pulling down and
then up on the latch (FN1664-E / FN1664SP-E only - Fig
10).
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
4. Remove the jammed fastener. In certain circumstances,
compliance for the products.
pliers may be required to remove the fastener.
5. Close the jam clearing nose door latch (FN1664-E /
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
FN1664SP-E only - Fig 11).
rien que les produits soient conformes aux normes CE.
6. Pull pusher back behind fasteners (FN1664-E /
FN1664SP-E) or close the magazine (BT1855-E,
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
BT1855SP-E, FN1650, FN1650SP-M, SX1838-E, SL540-M).
die CE-Richtlinien für Produkte.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
"DIAL-A-DEPTH™" FASTENER CONTROL
ADJUSTMENT (FIG 12A / 12B)
zeggen dat de producten voldoen aan de CE-vereisten.
The DIAL-A-DEPTH™ Fastener Control adjustment
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
feature provides close control of the fastener drive depth;
from flush with the work surface to shallow or deep
produkterne.
countersink. First, set the air pressure for consistent
drive in the specific work, then use the DIAL-A-DEPTH™
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
Fastener Control adjustment to give the desired depth of
yhdenmukaisuutta.
drive.
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα
TRIGGER LOCKOUT CONTROL - BT1855-E, SX1838-E,
αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
FN1664-E, FN1650 ONLY (FIG 13)
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
The trigger lockout control feature on BOSTITCH
pneumatic tools provides a trigger lock feature for added
conformità CE per i relativi prodotti.
safety control. Push the Lockout control button in or out
to activate or lock the tool trigger.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for
CE-merking for produktet.
ACTUATION MODE
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
m Warning! Always disconnect air supply before making
conformidade com a CE para os produtos.
adjustments as accidental actuation may occur, possibly
causing injury.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
SAFETY YOKE TYPE - BT1855SP-E, FN1650SP-M,
FN1664SP-E ONLY
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
These models operate differently from all other
conformidad con las normas CE de los productos.
BOSTITCH tools. To provide maximum visibility for
accurate fastener placement, the safety yoke of this tool
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
is normally in the "depressed" or "up" position. On all
nie stanowią deklaracji zgodności CE prezentowanych produktów.
other BOSTITCH tools and most other tools, the safety
yoke is normally in the "extended" or "down" position.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
This tool has a selectable actuation mode which
determines if the tool drives fasteners in sequential or
nie stanowią deklaracji zgodności CE prezentowanych produktów.
contact actuation mode. In sequential mode, when the
tip of the nose is placed on the work surface and the
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
trigger is pulled, the safety yoke moves out from the tool
výrobky.
to detect the work surface. The tool nose tip must be in
contact with the work surface to actuate. If the safety
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem
yoke does not detect the work surface close enough to
the nose of the tool, the tool will not actuate.
jelenti a termék CE-megfelelőségét.
In contact actuation mode, when the trigger is depressed
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
and held, the safety yoke will move out from the tool.
Contacting the work surface with the tool nose, will
conformitatea CE pentru produse.
actuate the safety yoke driving a fastener each time the
work surface is contacted.
SELECTABLE ACTUATION SYSTEM - ALL MODELS
These models feature a selectable actuation system that
allows the user to choose between the following modes
of operation.
m WARNING! Tools marked with this symbol
have either contact actuation, continuous
contact actuation or selectable actuation
with contact actuation selected.
WHEN IN CONTACT ACTUATION MODE:
These tools are designed for use in production
applications such as pallets, furniture,
manufactured housing or upholstery.
DO NOT use for applications such as closing boxes
or crates and fitting transportation safety systems
on trailers and lorries. This tool shall only be used in
safe working places. Care must be taken to prevent
accidental actuation when changing from one
working position to another.
SEQUENTIAL ACTUATION
The sequential actuation requires the operator to hold
the tool against the work with the safety yoke depressed
before pulling the trigger. In order to drive additional
fasteners, the trigger must be released and the tool
lifted away from the work, before repeating the above
mentioned steps.
This makes accurate fastener placement easier, for
instance on framing, toe nailing and crating applications.
The sequential actuation allows exact fastener location
without the possibility of driving a second fastener on
recoil, as described under Contact Trip (below). The
sequential actuation tool has a positive safety advantage
because it will not accidentally drive a fastener if the tool
is contacted against the work - or anything else - while
the operator is holding the trigger pulled.
CONTACT ACTUATION
The common operating procedure on "Contact
actuation" tools is for the operator to actuate the
safety trip while keeping the trigger pulled, thus driving
a fastener each time the work is contacted. This will
allow rapid fastener placement on many jobs, such as
sheathing, decking and pallet assembly. All pneumatic
tools are subject to recoil when driving fasteners.
The tool may bounce, releasing the safety yoke and
if unintentionally allowed to re-contact the work
surface with the trigger still actuated (finger still
holding the trigger pulled) an unwanted second
fastener will be driven.
GB
9
Werbung
