Herunterladen Inhalt Inhalt Diese Seite drucken

Stiga MP2 504 Serie Gebrauchsanweisung Seite 113

Vorschau ausblenden Andere Handbücher für MP2 504 Serie:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 81
use the machine until all the indications provided in
the "ASSEMBLY" section have been carried out.
4.1
ASSEMBLY COMPONENTS
The packaging includes assembly components.
4.1.1
Unpacking
1.
Cautiously open the packaging, paying 
attention not to lose components.
2.
Consult the documentation in the box, 
including these instructions.
Remove all the unassembled parts from the box.
3.
4.
Remove the machine from the box.
5.
Dispose of the box and packaging in 
compliance with local regulations.
4.2
GRASS-CATCHER ASSEMBLY
The grass-catcher is supplied fully assembled.
Make sure all the components are 
correctly assembled (fig. 3.A).
4.3
HANDLE ASSEMBLY
Open the handle to the working position carefully (fig. 4.A).
Insert the starter cable in the lower and upper 
spiral and tighten the nut (fig. 4.B).
5.
CONTROLS
5.1
HANDLE FOR MANUAL START
Enables manual starting of the engine (fig. 5.A).
5.2
ELECTRIC PUSH-BUTTON
IGNITION CONTROL
Enables electrical starting of
the engine (fig. 5.B).
5.3
THROTTLE CONTROL
Regulates the engine's r.p.m. (fig. 6.A).
The positions are indicated on the plate
showing the following symbols:
1. Full throttle. To be used always 
when the machine is running.
2. Minimum: used when the machine 
is sufficiently warm during stationary 
periods of operation.
3. "Choke" engaged. Used to turn
on the engine when cold.
5.4
SPEED CONTROL LEVER
The speed control lever allows the operator 
to regulate forward gear speed (fig. 7.A).
The positions are indicated on the plate
showing the following symbols:
1. Maximum speed.
2. Minimum speed.
IMPORTANT The engine must be
running and the drive engaged when
switching from one speed to another.
Do not touch the converter control when the engine
is off. Doing this could damage the converter.
NOTE If the machine does not move forward with the
lever in the «
» position, simply move the lever to «
» and then immediately return to the «
5.5
ENGINE BRAKE LEVER / CUTTING MEANS
It is the lever that allows you to switch the engine 
on and off whilst simultaneously engaging and 
disengaging the cutting means (fig. 8.A).
5.6
DRIVE ENGAGEMENT LEVER
It engages the wheel drive and allows 
the machine to move forward.
1. Drive engaged. Push the lever toward 
the handle for forward movement (fig. 
8.B). The lawnmower stops moving 
forward when the lever is released.
IMPORTANT
be ignited with the drive disengaged.
IMPORTANT
do not pull the machine backwards with the drive engaged.
5.7
CUTTING HEIGHT ADJUSTMENT
Lower or raise the chassis to cut the 
grass at different heights. 
Do this when the cutting means is stationary.
• "I" type adjustment.
The cutting height is adjusted by pressing the button 
(fig. 9.A) and, using the handgrip (fig. 9.B), lifting 
or lowering the chassis to the desired position.
• "Il" type adjustment.
The cutting height is adjusted by using the 
designated lever (fig. 9.C) that lifts or lowers 
the chassis to the desired position.
EN - 5
The engine must always
To prevent damage to the transmission,
» position.

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Mp2 554 serie

Inhaltsverzeichnis