Intended Use - Scheppach RO1200 Originalbetriebsanleitung

Introduction
MANUFACTURER:
scheppach Fabrikation von
Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
Improper handling,
•
Non-compliance of the operating instructions,
•
• Repairs by third parties, not by authorized service
technicians,
Installation and replacement of non-original spare
•
parts,
Application other than specified,
•
A breakdown of the electrical system that occurs
•
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
WE RECOMMEND:
Read through the complete text in the operating in-
structions before installing and commissioning the
device.
The operating instructions are intended to help the
user to become familiar with the machine and take
advantage of its application possibilities in accord-
ance with the recommendations.
The operating instructions contain important infor-
mation on how to operate the machine safely, pro-
fessionally and economically, how to avoid danger,
costly repairs, reduce downtimes and how to in-
crease reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country.
Always keep the operating instructions package with
the machine and store it in a plastic cover to protect
it from dirt and moisture. Read the instruction manual
each time before operating the machine and care-
fully follow its information. The machine can only be
operated by persons who were instructed concerning
the operation of the machine and who are informed
about the associated dangers. The minimum age re-
quirement must be complied with.
In addition to the safety requirements in these oper-
ating instructions and your country's applicable regu-
lations, you should observe the generally recognized
technical rules concerning the operation of wood-
working machines.
16 І GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Device Description (Fig. 1a / 1b/ 1c)
Extraction port
1
Routing shoe
2
Wing screw
3
ON/OFF switch
4
5 Safety lock-off
6 Handle
Speed control switch
7
Locking grip
8
Clamp nut
9
End stop revolver
10
Lock nut
11
12 Wing screw
13 Depth stop
Fine adjuster
14
Spindle lock button
15
Parallel stop
16
Nut
17
18 Long screw
19 Short screw
20 6 mm clamp
8 mm clamp
21
Guide sleeve
22
Open-ended spanner
23
Guide shaft
24
Unpacking
Open the packaging and remove the device care-
•
fully.
Remove the packaging material as well as the
•
packaging and transport bracing (if available).
Check that the delivery is complete.
•
• Check the device and accessory parts for trans-
port damage.
If possible, store the packaging until the warranty
•
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!

Intended use

The machine can be used for cutting notches, edges,
long holes and profiles, and it is suitable for contour
milling on workpiece surfaces such as wood, plas-
tics, light-weight materials or non-ferrous metals.
Any other use that is not explicitly approved in these
instructions may result in damage to the equipment
and represent a serious danger to the user. For se-
curity reasons, the device is not intended for children
and young people under the age of 16. Young peo-
ple aged 16 and over may only use the device un-
der adult supervision. The device is not designed for
commercial use. The manufacturer cannot be held
liable for damage when the appliance is not used in
conformity with its intended purpose or due to incor-
rect operation.