Walcom GENESI GEO Bedienungsanleitungen Seite 19

Mod. SLIM Conv SYSTEM
TECHNICAL SPECIFICATIONS
- Air fitting: G 1/4" M
- Product delivery fitting (version SP): G 1/4" M
- Maximum air pressure: 5 bar (73 psi)
- Maximum product pressure (SP version): 5 bar (73 psi)
ø FEED
1.0
SP
Gravity 184-286 Gr/min. (6.5-10 oz/min.)
1.3
SP
Gravity 174-182 Gr/min. (6.1-6.4 oz/min.)
Suction 190-192 Gr/min. (6.7-6.8 oz/min.)
1.5
SP
Gravity 280-282 Gr/min. (9.8-9.9 oz/min.)
Suction 160-180 Gr/min. (5.6-6.3 oz/min.)
1.7
SP
Gravity 290-294 Gr/min. (10.2-10.4 oz/min.)
Suction 206-218 Gr/min. (7.3-7.7 oz/min.)
1.9
SP
Gravity 270-332 Gr/min. (9.5-11.7 oz/min.)
2.2
Suction 168-228 Gr/min. (5.9-8 oz/min.)
Gravity 394-398 Gr/min. (13.9-14 oz/min.)
2.5
Suction 275-290 Gr/min. (9.7-10.2 oz/min.)
** Product flow was calculated with water, setting the recommended regulations.
USE
Spray guns in the SLIM series have been designed for the application of colours or paints or other fluid substances.
The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind.
To obtain the best results, the following instructions must be followed carefully:
1. When possible, use an air hose with a minimum internal section of ø 10 mm (0,37").
2. Make sure water, oil or other impurities are fully filtered from the compressed air used (for example, by installing a
WALCOM FSRD3/4 filter unit or the most complete and efficient WALCOM TD3/4 multifunction heat conditioner).
ADVICE FOR CORRECT USE
1. The distance between the spray gun and the surface to be painted must be set between 150 and 200 mm (5,9"-7,9").
If the spray gun is working at too low a pressure and at too high a distance, it will not perform to the best of its capacity.
2. The jet from the spray gun must always be perpendicular to the surface being painted and the paint must be applied in
horizontal strokes. Any eventual shift from this position when spraying
will result in an uneven application of the paint layer.
3. Correct viscosity of the paint is between 15 and 25 sec. Ford cup
n°4. These values depend on the application and the nozzle size
used.
SHAPE OF THE FAN
- Air pressure too low
- Product viscosity too high
- Quantity of product too high
Adjust the air pressure, product quantity and spray aperture
until obtaining a regular imprint as in fig. C
** PRODUCT LOAD
ADJUSTMENTS
- Working pressure: 2,5-3 bar (36-43 psi)
- Fan: Fully open
- Air: Fully open
- Product: 3,5-4,5 turns
FAN DIMENSIONS AT 20 cm (7.9")
18-20 cm (7.1"-7.9")
20-22 cm (7.9"-8.7")
25-27 cm (9.8"-10.6")
29-31 cm (11.4"-12.2")
23-25 cm (9"-9.8")
25-27 cm (9.8"-10.6")
26-28 cm (10.2"-11")
28-30 cm (11"-11.8")
25-28 cm (9.8"-11")
30-32 cm (11.8"-12.6")
26-27 cm (10.2"-10.6")
- Air pressure too high
- Product viscosity too low
- Quantity of product too low
19
AIR CONSUMPTION
220-260 l/min (7.4 - 8.7 CFM)
- Regular jet