Walcom GENESI GEO Bedienungsanleitungen Seite 17

Mod. GENESI HTE SYSTEM
TECHNICAL SPECIFICATIONS
- Air fitting: G 1/4" M
- Product delivery fitting (version SP): G 1/4" M
- Maximum air pressure: 5 bar (73 psi)
- Maximum product pressure (SP version): 5 bar (73 psi)
ø FEED ** PRODUCT LOAD
Gravity 108 Gr/min. (3.8 oz/min.)
0.8
SP
Gravity 139 Gr/min. (4.9 oz/min.)
1.0
SP
Gravity 170 Gr/min. (6 oz/min.)
1.2
SP
Gravity 192 Gr/min. (6.8 oz/min.)
1.3
SP
Gravity 204 Gr/min. (7.2 oz/min.)
1.4
SP
Gravity 271 Gr/min. (9.6 oz/min.)
Suction 154 Gr/min. (5.4 oz/min.)
1.7
SP
Gravity 291 Gr/min. (10.3 oz/min.)
Suction 166 Gr/min. (5.9 oz/min.)
1.9
SP
Gravity 357 Gr/min. (12.6 oz/min.)
Suction 235 Gr/min. (8.3 oz/min.)
2.5
SP
** Product flow was calculated with water, setting the recommended regulations.
At the recommended air pressure the spray gun works with at transfer efficiency superior to 65%.
USE
The GENESI HTE series of spray guns has been designed for the application of colours, paints or other fluid substances.
The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind.
To obtain the best results, the following instructions must be followed carefully:
The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind.
1. When possible, use an air hose with a minimum internal section of ø 10 mm (0,37").
2. Make sure water, oil or other impurities are fully filtered from the compressed air used (for example, by installing a
WALCOM FSRD3/4 filter unit or the most complete and efficient WALCOM TD3/4 multifunction heat conditioner).
ADVICE FOR CORRECT USE
1. The distance between the spray gun and the surface to be painted must be set between 150 and 200 mm (5.9 - 7.9").
If the spray gun is working at a too low pressure and at a too high distance, it will not perform to the best of its capacity.
2. The jet from the spray gun must always be perpendicular to the surface being painted and the paint must be applied in hori-
zontal strokes. Any eventual shift from this position when spraying
will result in an uneven application of the paint layer.
3. Correct viscosity of the paint is between 15 and 25 sec. Ford
cup n°4. These values depend on the application and the nozzle
size used.
SHAPE OF THE FAN
- Air pressure too low
- Product viscosity too high
- Quantity of product too high
Adjust the air pressure, product quantity and spray opening until
obtaining a regular imprint as in fig. C
FAN DIMENSIONS AT 20 cm (7.9")
RECOMMENDED AIR PRESSURE: 2 bar (29 psi)
ADJUSTMENTS
- Working pressure: 2-2,5 bar (29-36 psi)
- Fan: Fully open
- Air: Fully open
- Product: 3-4 turns
AIR CONSUMPTION AT 0.7 bar (10 psi) CAPTEST
15 cm (5.9")
18 cm (7.1")
20 cm (7.9")
21 cm (8.3")
22 cm (8.7")
24 cm (9.5")
21 cm (8.3")
25 cm (9.9")
22 cm (8.7")
27 cm (10.7")
23 cm (9.1")
- Air pressure too high
- Product viscosity too low
- Quantity of product too low
17
300-340 l/min (10 - 11.3 CFM)
- Regular jet