DeWalt DCF896 Bersetzt Von Den Originalanweisungen Seite 40

EnGLIsh
To remove an accessory, depress the detent pin through the
hole and pull the accessory off.
Anvil with Hog Ring (Fig. E)
DCF896H
To install an accessory on the hog ring anvil, firmly push
accessory onto the anvil . The hog ring
3
allow the accessory to slide on. After accessory is installed, the
hog ring applies pressure to help provide accessory retention.
To remove an accessory, grasp the accessory and firmly pull
it off.
nOTE: The thru-hole (Fig. E) allows an O-ring with retaining pin
or a 1-piece retaining pin to be used to help secure sockets and
accessories to the tool.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury. Exception—Tool Connect™
functions and mode adjustments require battery to
be installed.
NOTICE: Always check the tool configuration prior to
use. If you are unsure of the current configuration, press
the mode selector button
Home setting as described on the label and this manual.
Proper Hand Position (Fig. C)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
Usage
Your impact tool generates the following maximum torque:
Cat # Nm
Speed 3/2/1
DCF896, DCF896H 447/447/200
nOTE: Tool Connect™ custom speed settings will affect the
maximum torque output of the tool. Speeds lower than the
Home setting generally result in lower maximum torque.

CAUTION: Ensure fastener and/or system will withstand
the level of torque generated by the tool. Excessive torque
may cause breakage and possible personal injury.
1. Place the accessory on the fastener head. Keep the tool
pointed straight at the fastener.
2. Press switch to start operation. Release the switch to stop
operation. Always check torque with a torque wrench, as
the fastening torque is affected by many factors including
the following:
38
compresses to
17
9 (Fig. A) to set the tool to the
4 .
Ft.-Lbs. In.-Lbs
Speed 3/2/1 Speed 3/2/1
330/330/150 3960/3960/1800
Voltage: Low voltage, due to a nearly discharged
-
battery, will reduce fastening torque.
- accessory size: Failure to use the correct accessory size
will cause a reduction in fastening torque.
- Bolt size: Larger bolt diameters generally require
higher fastening torque. Fastening torque will also vary
according to length, grade, and torque coefficient.
Bolt: Ensure that all threads are free of rust and other
-
debris to allow proper fastening torque.
- Material: The type of material and surface finish of the
material will affect fastening torque.
- Fastening Time: Longer fasten ing time results in
increased fastening torque. Using a longer fastening
time than recom mended could cause the fasteners to
be overstressed, stripped or damaged.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.

WARNING: To reduce the risk of injury, use only D
impact-rated accessories.

WARNING: Use only impact-rated accessories. Non-
impact accessories may break and cause a hazardous
WALT recommended
e
WALT
e