DeWalt DCF896 Bersetzt Von Den Originalanweisungen Seite 38

EnGLIsh
To actuate the fuel gauge, press and hold the fuel gauge
button 14 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Belt Hook (Optional Accessory) (Fig. A)

WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
tool from a work belt. DO NOT use the belt hook for
tethering or securing the tool to a person or object during
use. DO NOT suspend tool overhead or suspend objects
from the belt hook.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook is secure.

CAUTION: To reduce the risk of personal injury or
damage, DO NOT use the belt hook to hang the drill
while using as a spotlight.
IMPORTanT: When attaching or replacing the belt hook
use only the screw that is provided. Be sure to securely
13
tighten the screw.
The belt hook 12 can be be attached to either side of the tool
using only the screw 13 provided, to accommodate left- or
right-handed users. If the belt hook is not desired at all, it can be
removed from the tool.
To move the belt hook 12 , remove the screw
it in place then reassemble on the opposite side. Be sure to
securely tighten the screw.
Variable Speed Trigger Switch (Fig. A)
To turn the tool on, squeeze the trigger switch
the tool off, release the trigger switch. Your tool is equipped
with a brake. The chuck will stop when the trigger switch is
fully released.
The variable speed switch enables you to start the application at
a slow speed. The further you squeeze the trigger, the faster the
tool will operate. For maximum tool life, use variable speed only
for starting holes or fasteners.
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
Forward/Reverse Control Button (Fig. A)
A forward/reverse control button
the tool and also serves as a lock-off button.
To select forward rotation, release the trigger switch and
depress the forward/reverse control button on the right side of
the tool.
To select reverse, depress the forward/reverse control button on
the left side of the tool. The centre position of the control button
locks the tool in the off position. When changing the position of
the control button, be sure the trigger is released.
36
12 ,
13 that holds
. To turn
1
determines the direction of
2
nOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate a problem.
Worklight (Fig. A)
There is a worklight 7 located on the foot of the tool. The
worklight will be activated when the trigger switch is depressed.
When the trigger is released, the worklight will stay illuminated
for up to 20 seconds. If the trigger switch remains depressed,
the worklights will remain on.
nOTE: The worklight is for lighting the immediate work surface
and are not intended to be used as a flashlight.
Tool Connect™ Mode Selector (Fig. A)

WARNING: To reduce the risk of injury, remove
accessories from the tool chuck before using the
mode selector.
The DCF896 and DCF896H are equipped with a mode
selector that allows Modes 1, 2 (Precision Wrench™ mode),
and 3, to be customized using the Tool Connect™ app. Home
settings are active when the home light indicator
and is not customizable. The 4 features listed in Table 1 can
be customized.
Once configured, pressing the mode selector button
foot of the tool will cycle through the modes
If you are unsure of the current configuration, press the mode
selector button to set the tool to the Home setting (home
9
indicator 10 is lit).
Precision Wrench™
In addition to normal impacting modes, this tool features
the Precision Wrench™ mode which grants the user greater
control in both fastening and loosening applications. When
set in forward, the tool will fasten at 2000 RPM until impact
begins. The tool will then pause for a duration set by the user
in ToolConnect™, providing the user with greater control and
reducing the chance of overtightening or damaging material.
When set in reverse, the tool will impact at a normal speed and
rate of 3100 IPM in reverse. Upon sensing that the fastener has
broken free, the tool will cease to impact and will reduce speed
to help prevent "run-off" of loose hardware. Speed reduction
can be set by the user in ToolConnect™.
Impact Time
Tool will automatically shut off after impacting for a specific
time limit set by the user in the Tool Connect™ app.
Precision Tap™

WARNING: Use only impact-rated taps and accessories.

WARNING: Tapping not recommended for use on critical
or precision workpieces.

WARNING: Tap life is heavily affected by tool alignment
with the workpiece, speed settings, material condition
and lubrication.

WARNING: Tap breakage may occur if tap is driven too
far without clearing chips. Choose tapping speed and time
10 is lit
9 on the
11 .