Makita AN635H Betriebsanleitung Seite 12

Nose adapter
To prevent the surface of workpiece from being
scratched or damaged, use the nose adapter.
To detach the nose adapter from its housing base, pull
the nose adapter with your thumb in the direction of the
arrow.
► Fig.8: 1. Nose adapter
To attach the nose adapter to the contact element,
press it onto the contact element until the recessed
parts in three places inside the nose adapter fit in three
protrusions of the contact element.
► Fig.9: 1. Nose adapter 2. Contact element
3. Protrusion 4. Recessed part
Air duster
CAUTION:
Do not aim the ejection port of the
air duster to someone. Also, keep your hands and
foot away from the ejection port. If the air duster
button is accidentally pushed, it may cause a per-
sonal injury.
CAUTION:
Always check your surroundings
before using the air duster. Blown dust or objects
may hit someone.
CAUTION:
Do not connect or disconnect the
air hose while pushing the air duster button.
The air supplied to the tool can also be used as an air
duster. You can clean the work area by pressing the
button on the grip end.
► Fig.10: 1. Button
NOTICE:
After using the air duster, the driving force
of the tool will temporarily decline. Wait until the air
pressure recovers in this case.
NOTICE:
Perform a test blow if you use the air
duster immediately after the oil was applied. The oil
may be sprayed with the air.
ASSEMBLY
CAUTION:
Before carrying out any work on
the tool, always lock the trigger by turning the
trigger lock lever to the lock position
disconnect the air hose from the tool.
Loading nailer
CAUTION:
Do not use deformed nails or
linked sheet.
1. Disconnect the air hose.
2.
Depress the latch lever and open the door and
magazine cap.
► Fig.11: 1. Latch lever 2. Door 3. Magazine cap
► Fig.12
3. Turn the adjust shaft and set the step of the
change plate suitable for the nail length. Make sure that
the arrow points to the corresponding graduation incre-
ment of the nail length marked on the adjust shaft.
► Fig.13: 1. Change plate 2. Adjust shaft 3. Arrow
NOTICE:
plate set to the wrong step, it may result in poor nail
feeding or tool malfunction.
4.
Place the nail coil over the change plate and
uncoil enough nails to reach the nail rail.
Then place the first nail in the nail rail and the second
nail in the feed claw. Also, place other uncoiled nails on
feeder body.
► Fig.14: 1. Nail rail 2. Feed claw
5.
Check that the nail coil is set properly in the
magazine.
6. Close the magazine cap carefully. Then with
depressing the latch lever, close the door until the latch
lever locks.
Connecting air hose
CAUTION:
a finger on the trigger. An unexpected driving will
cause serious injury.
► Fig.15: 1. Air fitting 2. Air socket
Slip the air socket of the air hose onto the air fitting on
the tool. Be sure that the air socket locks firmly into
position when installed onto the air fitting.
A hose coupling must be installed on or near the tool in
such a way that the pressure reservoir will discharge at
the time the air supply coupling is disconnected.
Changing the trigger for contact
actuation mode
CAUTION:
and unload the tool with nails before replacing
the trigger.
CAUTION:
always check that the tool operates properly
before actual work. Do not load the tool with any
nails before checking the function to avoid unex-
pected nailing.
The trigger for single sequential actuation mode is
, and
factory-installed. To change the nailing mode to contact
actuation, replace the trigger part with the one for con-
tact actuation.
► Fig.16: 1. Trigger for single sequential actuation
1. Turn the trigger lock lever to the lock position
► Fig.17: 1. Trigger lock lever
2.
Push the pin securing the trigger from the ure-
thane washer side, and then remove the urethane
washer. Then pull out the pin and remove the trigger.
► Fig.18: 1. Pin 2. Urethane washer 3. Trigger
12 ENGLISH
If the tool is operated with the change
Do not connect the air hose with
Always disconnect the air hose
After the trigger replacement,
(Gray color) 2. Trigger for contact actuation
(Black color)
.