Maintenance And Service; Maintenance And Cleaning - Bosch PFS 1000 Originalbetriebsanleitung

20 | English
Air cap Spray jet pattern Application
Setting the spray material quantity (see figure G)
(PAINTVolume)
– Turn the thumbwheel (5) to set the required spraying ca-
pacity:
−: Minimum quantity of spraying material,
+: Maximum quantity of spraying material.
Spraying capacity Setting
Too much material on target The spraying capacity must
area: be reduced.
– Turn the thumbwheel (5)
Not enough material on tar- The spraying capacity must
get area: be increased.
– Turn the thumbwheel (5)
Dampening Wallpaper
To make it easier to remove old wallpaper, you can spray
warm water on the wallpaper (max. 55 °C). Use the grey
nozzle cap (8) to do so.
Work breaks and transport (see figure H–I)
A carrying handle (21) and a carrying strap (22) are fitted to
the base unit to enable easy transport of the fine-spray sys-
tem.
You can hang the base unit (19) across your shoulder during
work using the carrying strap (22).
The spray gun (1)can be put down on a flat work surface dur-
ing breaks. No spray material can leak out.
Always put the spray gun upright on a flat surface
u
when it is filled with spray material. Spray material can
leak out from a spray gun if it is lying down.
1 609 92A 58F | (12.11.2019)

Maintenance and Service

Horizontal flat jet

Maintenance and Cleaning

for vertical working
direction
u
u
Vertical flat jet for
horizontal working
In order to avoid safety hazards, if the power supply cord
direction
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Round jet for u
corners, edges and
hard to reach loca-
tions
Cleaning the air filter (see figure J)
The air filter (26) must be cleaned occasionally. The air filter
must be replaced if it is heavily soiled.
– Open the air filter cover (23).
– Remove the air filter (26).
– Light contamination:
in direction –.
– Reinsert the air filter.
– Close the air filter cover (23) again.
in direction +.
Cleaning the fine spraying system (see figure K)
Always clean the spray gun and the container with the re-
spective diluting agent (paint thinner or water) for the spray
material being used.
Never clean the nozzle and air holes in the spray gun with
pointed objects.
– Switch the base unit (19) off.
– Remove the air hose (17) both from the base unit (19)
– Clean the base unit if necessary with a cloth moistened
– Press the trigger switch (6) on the spray gun so that the
– Unscrew the container (7) and empty the remaining
– Fill the container (7) halfway with the diluting agent
Pull the plug out of the socket before carrying out any
work on the power tool.
To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
Thoroughly clean the individual parts of the fine-spray
system after each use, especially all paint-carrying
components. Proper cleaning is a prerequisite for fault-
less and safe operation of the spray gun. No warranty
claims will be accepted if cleaning has not been done at
all or has not been done properly.
Knock on the air filter (26).
or
Heavy contamination:
Clean the air filter (26) under running water and sub-
sequently leave it to dry thoroughly, in order to prevent
mould from forming.
or
Replace the air filter (26).
and from the spray gun (1)(quarter turn of the bayonet
lock (18) anticlockwise; pull the bayonet lock (18) out of
the port (4)/(24)).
with diluting agent and then remove the base unit (19)
and the air hose (17) from the immediate cleaning envir-
onment.
spray material can flow back into the container.
spray material back into the original spray material.
(solvent or water) and fit it to the spray gun (1)again.
Bosch Power Tools