Starting Operation; Switching Off; Working Advice - Bosch PFS 1000 Originalbetriebsanleitung

When diluting the spray material, make sure that the
u
flash point of the mixture is above 55 °C again after di-
luting. Diluting substances such as solvent-based lac-
quers lowers the flash point.
Filling the spray material (see figures D1–D2)
Note: Remove the air hose (17) before pouring in spray ma-
terial (quarter turn of the bayonet lock (18) anticlockwise;
pull the bayonet lock (18) out of the port (4)).
– Unscrew the container (7) from the spray gun.
– Pour the spray material into the container (7) up to no
more than the 800 mark.
– Turn the suction tube (12) so that the spray material can
be sprayed with almost no residue:
For spray jobs on horizontal Towards the front in the dir-
surfaces/objects ection of the nozzle/air cap
For spray jobs overhead Towards the rear in the dir-
ection of the handle
– Carry out a test-spray run on a test surface.
If the spray pattern is optimal, you can begin spraying.
or
If the spraying results are unsatisfactory or no paint is emit-
ted: (see "Troubleshooting", page 21)

Starting Operation

Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the power tool.
Make sure that the base unit cannot draw in dust or
u
other contamination during operation.
Make sure never to spray on the base unit.
u
Stop spraying if fluid escapes from places other than
u
the intended nozzle during spraying, and restore the
spray gun to its proper condition. There is a risk of elec-
tric shock.
Do not direct the fine-spray system against yourself,
u
other persons or animals.
Switching on (see figure E)
– PFS 2000: Check whether the correct nozzle cap is fit-
ted. (see "Changing the nozzle cap (PFS 2000) (see fig-
ure C)", page 18)
– Plug the mains plug into a plug socket.
– Grasp the spray gun by the handle and point it at the tar-
get area.
– Slide the on/off switch (20) forwards.
– Pull the trigger switch (6) on the spray gun.
Note: Air always flows out at the air cap (2) when the base
unit is switched on.

Switching Off

– Let go of the trigger switch (6) and slide the on/off
switch (20) backwards.
– Pull the mains plug from the plug socket.
Bosch Power Tools

Working Advice

Spraying (see figure F)
Note: Pay attention to the wind direction when you are using
the power tool in the open air.
– Firstly, carry out a test-spray run and adjust the spray pat-
tern and the spray material quantity according to the
spray material.
For adjustments, see the following sections.
– Make sure to hold the spray gun with a uniform clearance
of 20–25 cm vertical to the object being sprayed.
– Begin the spraying procedure outside the target area.
– Move the spray pistol evenly horizontally or vertically ac-
cording to the spray pattern configuration.
An even surface quality can be achieved when the spray
paths overlap by 4–5 cm.
– When spraying horizontal objects or spraying overhead,
hold the spray gun at a slight angle and move back from
the sprayed surface.
Risk of tripping! Be aware of potential obstacles in the
room.
– Avoid interruptions when spraying the target area.
Guiding the spray gun evenly will provide uniform surface
quality.
A non-uniform spraying angle and distance will lead to heavy
formation of paint mist and consequently an uneven surface.
– End the spraying procedure outside the target area.
Never completely empty the container for the spray material
by spraying. If the suction tube is no longer immersed in the
spray material, the spray jet will be interrupted and this will
result in an inconsistent surface.
– If the spray material settles on the air cap (2) or the
nozzle cap, clean the components with the diluting agent
used.
Adjusting the spray pattern
Never actuate the trigger switch (6) while adjusting
u
the air cap (2).
– Turn the air cap (2) to the required position.
English | 19
1 609 92A 58F | (12.11.2019)