Safety Instructions For Fine Spray Systems; Product Description And Specifications; Intended Use - Bosch PFS 1000 Originalbetriebsanleitung

16 | English
Power tool use and care
Do not force the power tool. Use the correct power
u
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was de-
signed.
Do not use the power tool if the switch does not turn it
u
on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or the
u
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk
of starting the power tool accidentally.
Store idle power tools out of the reach of children and
u
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or bind-
u
ing of moving parts, breakage of parts and any other
condition that may affect the power tool's operation.
If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power
tools.
Keep cutting tools sharp and clean. Properly main-
u
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
u
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.

Safety instructions for fine spray systems

Keep your work area clean, well lit and free of paint or
u
solvent containers, cloths and other flammable mater-
ials. Possible risk of spontaneous combustion. Ensure
that you have access to functioning fire extinguishers at
all times.
Ensure that the spray area is well ventilated and that
u
there is sufficient fresh air circulating in the whole
area. Evaporating flammable solvents create an explosive
environment.
Do not spray or clean with materials with a flash point
u
lower than 55 °C. Use water-based materials, non-
volatile hydrocarbons or similar materials. Volatile
evaporating solvents create an explosive environment.
Do not spray near ignition sources such as static elec-
u
tricity sparks, naked flames, pilot lights, hot objects,
engines, cigarettes and sparks created by plugging in
and unplugging electric cables or operating switches.
These kinds of spark sources can lead to combustion of
the surrounding environment.
1 609 92A 58F | (12.11.2019)
Do not spray materials if it is not clear whether they
u
might be dangerous. Unknown materials could create
hazardous conditions.
Do not spray wallpaper stripper or boiling water.
u
Spray only warm water (max. 55 °C) which is free
from chemical additives.
Wear additional personal protection equipment such
u
as appropriate protective gloves and a protective
mask or respirator when spraying or handling chemic-
als. Wearing personal protection equipment appropriate
to the conditions reduces your exposure to hazardous
substances.
Take note of possible risks posed by the spray mater-
u
ial. Observe the markings on the container or the man-
ufacturer's information regarding the spray material,
including the instructions about using personal pro-
tective equipment. You must comply with the manufac-
turer's instructions in order to reduce the risk of fire and
of injury caused by poison, carcinogens, etc.
Keep the mains plug and the spray gun trigger switch
u
free from paint and other liquids. Never hold the cable
by its plug connection for support. Doing this could
cause electric shock.
Supervise children. This will ensure that children do not
u
play with the fine spray system.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.

Intended Use

PFS 1000
The power tool is only intended for atomising solvent-based
and water-dilutable lacquers, glazes, primers, clear lac-
quers, oils and water.
Bosch Power Tools