Adjustment; Maintenance And Service; Maintenance And Cleaning - Bosch PFS 5000E Originalbetriebsanleitung

OBJ_BUCH-2026-003.book Page 23 Thursday, April 2, 2015 9:28 AM
Adjusting the Spraying Capacity (see figure J)
(PAINTVolume)
– Turn the thumbwheel 4 to set the required spraying capac-
ity:
Settings 1/2/3: "wood/glaze/lacquer" application,
Settings 4/5: "wall" application.
Spraying capacity
Too much material on target ar-
ea:
Not enough material on target
area:
Adjusting the Air Flow (see figure D)
(AIRVolume)
– Turn the air flow control 25 to select the appropriate appli-
cation in order to set the correct air flow and pressure for
the spray material used.
Setting the Applications
Thin-viscosity spray material Thick-viscosity spray material
25
"Wood/glaze application" "Wood/lac-
quer" applica-
tion
The air flow and pressure can be steplessly adjusted within an
application.
Too much fog of coating material:
The air flow must be reduced.
– Turn the air flow control 25 to the left.
Atomisation too coarse:
The air flow must be increased.
– Turn the air flow control 25 to the right.
Bosch Power Tools
Dampening wallpaper
To make it easier to remove old wallpaper, you can spray
warm water on the wallpaper (max. 55 °C).
Use the grey nozzle cap 11 to do so.
Work Breaks and Transport (see figures K – L)
A carrying handle 23 is fitted to the base unit to enable easy

Adjustment

transport of the fine-spray system.
The spraying capacity must
Wheels are fitted to the bottom of the base unit 22. You can
be reduced.
pull the base unit behind you by the air hose 20 during work.
– Turn down by one setting.
The spray gun 1 can be put down on a flat work surface during
breaks. No spray material can leak out.
 Always put the spray gun upright on a flat surface when
The spraying capacity must
be increased.

Maintenance and Service

– Turn up by one setting.

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains
 Thoroughly clean the individual parts of the fine-spray
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Cleaning (see figure M)
Always clean the spray gun and the container with the respec-
tive diluting agent (paint thinner or water) for the spray mate-
rial being used.
Never clean the nozzle and air holes in the spray gun with
pointed objects.
– Switch the base unit 22 off.
– Remove the air hose 20 both from the base unit 22 and
– Clean the base unit if necessary with a cloth moistened
"Wall" appli-
cation
– Press the trigger switch 5 on the spray gun so that the
– Unscrew the container 7 and empty the remaining spray
– Fill the container 7 halfway with the diluting agent (solvent
– Shake the spray gun several times.
– Unscrew the container 7 and empty the container com-
– Remove the union nut 3, the air cap 2, the nozzle cap used
it is filled with spray material. Spray material can leak
out from a spray gun if it is lying down.
plug.
system after each use, especially all paint-carrying
components. Proper cleaning is a prerequisite for fault-
less and safe operation of the spray gun. No warranty
claims will be accepted if cleaning has not been done at all
or has not been done properly.
from the spray gun 1 (quarter turn of the bayonet lock 21
counterclockwise; pull the bayonet lock 21 out of the port
9/26).
with diluting agent and then remove the base unit 22 and
the air hose 20 from the immediate cleaning environment.
spray material can flow back into the container.
material back into the original spray material.
or water) and fit it to the spray gun 1 again.
pletely into an empty material tin.
10/11/12 and the suction tube 17 with the container seal
16.
English | 23
1 609 92A 164 | (2.4.15)