Operation Modes - Vitek VT-1621 W Betriebsanweisung

ENGLISH
•
For children safety reasons do not leave polyethyl-
ene bags, used as a packaging, unattended.
•
Attention! Do not allow children to play with poly-
ethylene bags or packaging film. Danger of suf-
focation!
•
If the unit was dropped into water:
– do not touch the water;
– unplug the unit immediately, only after that you
can take the unit out of the water;
– apply to the authorized service center for testing
and repairing the unit.
•
Never use the unit if the power cord or the power
cord plug is damaged, the unit works improperly
or after it was dropped.
•
Do not dismantle the unit by yourself. If any mal-
function is detected or after the unit was dropped,
apply to the nearest authorized service center.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and disabled
persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USAGE
ONLY
BEFORE USING THE UNIT
After unit transportation or storage at low tem-
perature it is necessary to keep it for at least two
hours at room temperature before switching on.
– Unpack the unit completely and remove any stick-
ers that can prevent unit operation.
– Check the unit for damages; do not use it in case
of damages.
– Before switching the unit on, make sure that volt-
age of the mains corresponds to unit operating
voltage.
– Wash all removable parts (3-19) with warm water
and a neutral detergent, then rinse them and dry.
– Clean the motor unit (1) with a soft, slightly damp
cloth and then wipe it dry.
Attention!
•
Do not immerse the motor unit (1), the power
cord and power plug into water or any other
liquids.
•
Do not put the attachments and bowls in a
dishwashing machine.
•
Attention! The cutting edges of the chopping
knife (12), the knife block (20), the slicing/
grating attachments (9-11) are sharp and dan-
gerous, be very careful when cleaning them!

OPERATION MODES

To select the attachment rotation speed, set the opera-
tion mode switch (2) to the corresponding position:
«0» - the unit is off
«1» - low rotation speed
«2» - high rotation speed
VT-1621.indd 4
– To operate the unit in the pulse mode, turn and
hold the knob of the operation mode switch (2) in
the position «P».
Amount of products
Make sure that the amount of liquid products doesn't
exceed the maximal values: - 1200 ml in the process-
ing bowl (4) and 1800 ml in the blender bowl (19). Do
not make more than 330 g dough at a time when using
the attachment (13).
USING THE BLENDER
The blender is used for mixing or beating various liq-
uids, chopping soft fruit and vegetables. Do not pro-
cess hard fruit and vegetables, fruit with stones, hard
cheeses, ice etc. in the blender.
– Before chopping/mixing products, we recom-
mend to peel fruit or vegetables, remove inedible
parts (such as stones), and cut fruit or vegetables
into approximately 2х2 cm cubes.
WARNING: Before assembling the unit, make sure
that the power plug is not inserted into the socket.
– Make sure that the knife block (20) is set and fixed
properly in the blender bowl (19).
– Set the blender bowl (19) on the motor unit (1)
matching the marks «» and «
(19) clockwise until the marks «» and « » match.
If the bowl is set properly, you'll hear a click.
– Insert the plug/measuring cup (17) into the lid
(18), matching the ledges on the cup with the
grooves on the lid, and turn the cup (17) clockwise
as far as it will go.
Note: Before using the blender, make sure that the
plug/measuring cup (17) is installed in the lid (18),
otherwise the processed liquid may splash through
the lid (18) opening.
– Put the food into the blender bowl (19), cover the
bowl with the lid (18).
– Insert the power plug into the mains socket. The
blender is ready for operation.
– Select the required knives rotation speed with the
operation mode switch (2), for short time opera-
tion use the pulse mode, to switch the pulse mode
on, turn and hold the switch (2) knob in the posi-
tion «P».
– During the operation or between the operations
you can add the required ingredients into the bowl
(19). To do this, turn the lid plug/measuring cup (17)
counterclockwise and remove it, you can use the cup
(17) as a bowl for adding necessary liquid ingredi-
ents. After adding the ingredients, place the cup (17)
back to its place and turn it clockwise until it is fixed.
– After the unit operation is finished, set the opera-
tion mode switch (2) knob to the position «0» and
unplug the unit.
4
». Turn the bowl
16.12.2013 9:49:08