Important Remarks; Important Safety Instructions - Cardin Elettronica EL3424 Bedienungsanleitung

IMPORTANT REMARKS

TO REDUCE THE RISK OF SEVERE INJURY OR DEATH READ THE FOLLOWING REMARKS
CAREFULLY BEFORE PROCEEDING WITH THE INSTALLATION. PAY PARTICULAR ATTENTION
TO ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
INSTRUCTIONS COULD COMPROMISE THE CORRECT WORKING ORDER OF THE SYSTEM.
•
These instructions are aimed at professionally qualified "INSTALLERS
OFELECTRICALEQUIPMENT"andmustrespectthelocalstandards
and regulations in force. All materials used must be approved and
must suit the environment in which the installation is situated.
• All maintenance operations must be carried out by professionally
qualified technicians. Before carrying out any cleaning or maintenance
operations make sure the power is disconnected at the mains and
that the 24V battery supply Faston V5 has been disconnected.
• This appliance must be used exclusively for the purpose for which it
has been made. "i.e. for traffic control".
The appliance may be used to control passageways with widths of
3m and 4m.
• The unit may be fitted both to the right and to the left of the pas-
sageway.
• The automation is fitted with an anti-tamper system protecting its
internal mechanisms. If the system is forced it will release the boom
and boom holder from the mechanism thus protecting it from damage.
Normal operation can be obtained by replacing the broken safety
pin.
• This product and all its relative components has been designed and
manufactured by Cardin Elettronica who have verified that the product
conforms in every aspect to the safety standards in force.
Any non authorised modifications are to be considered improper
and therefore dangerous. The manufacturer accepts no liability for
situations arising from the use of an electrical installation which does
not conform to the local standards and regulations in force and in
particular when the earthing circuit is not efficient.

IMPORTANT SAFETY INSTRUCTIONS

It is the responsibility of the installer to make sure that the following
public safety conditions are satisfied:
1) Ensure that the gate operating installation is far enough away from
the main road to eliminate possible traffic disruptions.
2) The operator must be installed on the inside of the property and not
on the public side of the gate. The gates must not swing outwards
onto a public area.
3) The gate operator is designed for use on gates through which vehicles
are passing. Pedestrians should use a separate entrance.
4) The gate must be in full view when it is operating therefore controls
must be situated in a position where the operator can see the gate
at all times.
5) At least two warning signs (similar to the example on the right) should
be placed, where they can be easily seen by the public, in the area
of the system of automatic operation. One inside the property and
one on the public side of the installation.
These signs must be indelible and not hidden by any objects (such
as tree branches, decorative fencing etc.).
6) Make sure that the end-user is aware that children
and/or pets must not be allowed to play within the
area of a gate installation. If possible include this
in the warning signs.
7) A correct earth connection is fundamental in order
to guarantee the electrical safety of the machine
8) If you have any questions about the safety of the
gate operating system, do not install the operator.
Contact your dealer for assistance.
TECHNICAL DESCRIPTION
710/EL3424
Automation for 3m and 4m booms with a 24Vdc motor. The incorporated
electronic programmer contains the power stage, the logic control, the
battery charger and the radio receiver module. The power supply is
routed to the electronics card via a separate transformer which is housed
in the same container.
710/EL324K1
3-meter boom in extruded aluminium complete with boom lights and
a rubber buffer. Flashing warning lights on the boom (using LED tech-
nology).
IMPORTANT REMARKS
710/EL424K1
4-meter boom in extruded aluminium complete with boom lights and
a rubber buffer. Flashing warning lights on the boom (using LED tech-
nology).
716/EL3424ASKU
3m articulated boom complete with a rubber buffer. A special device
inside the bar allows it to fold backwards when the barrier is opening.
• 24Vdc motor with tempered steel never ending screws;
- lockable flip-back upper hood in shock-proof plastic fitted with
emergency stop microswitches;
- manual release handle in nylon reinforced with glass fibre;
- irreversible second stage reduction unit with tempered steel gears
and first stage reduction worm gear in highly reliable self-lubricat-
ing POM, mounted on a cast aluminium stator;
- zinc-plated steel geared motor support base;
- boom support levers and joints in zinc-plated steel;
- balancing springs in highly reliable steel;
- lubrication using permanently fluid grease;
- barrier bodywork in spray painted aluminium;
- lockable access door fitted with emergency stop microswitches
giving access to the manual release components;
- incorporated warning lights;
- incorporated boom lights;
- closing direction travel limit allowing the position of the boom to
be adjusted horizontally;
- adjustable opening direction travel limit with setting screw;
- self-rupturing security screw supplied with the appliance.
WARNINGS FOR THE USER
Have the appliance controlled and checked at regular intervals by spe-
cialised maintenance personnel:
- Check to be carried out after the first 200.000 manoeuvres (or six
months after the installation);
Periodically check the correct operation of all safety devices (photo-
electric cells etc.).
Eventual repair work or maintenance must be carried out by specialised
personnel using original spare parts.
In case of failure or operational anomalies switch off the power
at the mains and call the after sales service, do not attempt to
repair the appliance yourself.
The appliance is fitted with batteries therefore to cut off the power
WARNING
supply you will have to open the contact between binding posts 7
and 8 "EMRG" (this could be carried out by activating an external
AUTOMATIC OPENING
KEEP CLEAR
normally closed contact button).
Opening the access door and/or the flip-back hood will block
the appliance.
Closing both of these access points will reset normal operation:
if the boom is not closed, after a 10-second time period has
elapsed it will close automatically without waiting for an external
CHILDREN OR PETS MUST NOT
BE ALLOWED TO PLAY ON OR
NEAR THE INSTALLATION
command.
WARNINGS FOR THE INSTALLER
The minimum controls which may be installed are OPEN-STOP-CLOSE,
these controls must be installed in a location not accessible to chil-
dren.
During the opening/closing manoeuvre check for correct operation and
activate the emergency stop button in case of danger.
During blackouts the boom can be released and manually manoeuvred
(see manual manoeuvre pag. 20).
18
IMPORTANT REMARKS
. NOT READING THESE IMPORTANT