Important Remarks; User Instructions; Important Safety Instructions; Installation Instructions - Cardin Elettronica EL Serie Bedienungsanleitung

IMPORTANT REMARKS

READ THE FOLLOWING REMARKS CAREFULLY BEFORE PROCEEDING WITH THE INSTALLATION.
PAY PARTICULAR ATTENTION TO ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
READING THESE IMPORTANT INSTRUCTIONS COULD COMPROMISE THE CORRECT WORKING
ORDER OF THE SYSTEM AND CREATE DANGER SITUATIONS FOR THE USERS OF THE SYSTEM.
• These instructions are aimed at professionally qualified "installers
of electrical equipment" and must respect the local standards and
regulations in force. All materials used must be approved and must
suit the environment in which the installation is situated.
• All maintenance operations must be carried out by professionally
qualified technicians. Before carrying out any cleaning or maintenance
operations make sure the power is disconnected at the mains.
• This appliance must be used exclusively for the purpose for which
it has been made. "i.e. for traffic control". The appliance may be
used to control passageways with a maximum width of 3 m.
• The unit may be fitted both to the right and to the left of the pas-
sageway.
• This product and all its relative components has been designed and
manufactured by Cardin Elettronica who have verified that the product
conforms in every aspect to the safety standards in force.

IMPORTANT SAFETY INSTRUCTIONS

It is the responsibility of the installer to make sure that the following
public safety conditions are satisfied:
1) Ensure that the boom operating installation is far enough away from
the main road to eliminate possible traffic disruptions.
2) In its vertical movement the boom must not come into contact with
overhead cables and other such obstacles.
3) The boom operator is designed for use on passageways through
which vehicles are passing. Pedestrians should use a separate
entrance.
4) The boom must be in full view when it is operating therefore controls
must be situated in a position where the operator can see the boom
at all times.
5) At least two warning signs (similar to the example
on the right) should be placed, where they can be
easily seen by the public, in the area of the system
of automatic operation. One inside the property
and one on the public side of the installation.
These signs must be indelible and not hidden by
any objects (such as tree branches, decorative
fencing etc.).
6) Make sure that the end-user is aware that children
and/or pets must not be allowed to play within the area of an auto-
matic installation. If possible include this in the warning signs.
7) A correct earth connection is fundamental in order to guarantee the
electrical safety of the machine
8) If you have any questions about the safety of the barrier operating
system, do not install the operator. Contact your dealer for assist-
ance.
TECHNICAL DESCRIPTION
710/EL3024 Electromechanical barrier with a 24Vdc motor, incor-
porated electronics, buffer battery, automatic and
semiautomatic functions, torque limiter and S449
radio frequency decoder.
716/EL3024A Ø 60 mm - 3000 mm long bar complete with bar
holder arm with which to connect it to the barrier
- 24Vdc motor with a steel never ending screw.
- Carter in shock-proof plastic.
- Manual release components in reinforced plastic.
- Geared motor with steel gears enclosed in a die cast two-piece
aluminium shell.
- Motor support base in zinc-plated steel
- Boom holder in die cast aluminium.
- Lubrication using permanently fluid grease.
- Barrier cabinet in spray painted die cast aluminium.
- Incorporated warning light.
IMPORTANT REMARKS

USER INSTRUCTIONS

Suitable differential collection, environmental friendly treatment and disposal
contributes to avoiding negative effects on the ambient and consequently
health as well as favouring the recycling of materials.
Illicitly disposing of this product by the owner is punishable by law and will
be dealt with according to the laws and standards of the individual member
nation.
During the opening/closing manoeuvre check for correct operation
and activate the emergency stop button in case of danger.
During blackouts the gate can be released and manually manoeuvred
(see manual release pag.12).
Attention! The boom is not balanced and must be held
during manual release
Periodically check the correct operation of all safety devices (photo-
electric cells etc.)
Eventual repair work must be carried out by specialised personnel
using original spare parts.
The appliance is suitable for continuous operation (see technical data
on page 20).
WARNING
AUTOMATIC OPENING
KEEP CLEAR

INSTALLATION INSTRUCTIONS

• The minimum controls which may be installed are OPEN-STOP-
CLOSE, these controls must be installed in a location not accessible
to children.
CHILDREN OR PETS MUST NOT
• The ground must be stable enough to firmly hold the plinth and the
BE ALLOWED TO PLAY ON OR
NEAR THE INSTALLATION
anchor plates.
• Where possible protect the barrier cabinet from accidental knocks
by passing vehicles.
• Work out the run of the cables according to the command and
control devices fitted and make sure the system conforms to the
local standard and regulations in force (see installation example
fig.1 pag. 2).
FITTING THE UNIT
- prepare a cement base with the base plate and anchors "A" embed-
ded. The cable passage tube "B" and the four threaded bolts "D"
M8 must protrude (30mm) from the base plate.
- the base plate must be perfectly in square, its surface must be
clean and the four threaded bolts must emerge perpendicularly.
Note: the cement base should preferably protrude 50 mm out of
the ground in order to avoid water build up which could damage
the appliance.
• To install the barrier proceeds as follows:
- remove the 4 self locking nuts "D" from the four threaded bolts
(used to fasten down the anchors) and insert the base of the bar-
rier "C". Fasten down the barrier using the 4 self locking nuts and
washers "D" supplied with the appliance.
- it is also possible to fasten the barrier to an already existing cement
base as long as the thickness of the base is great enough to guar-
antee a strong hold for the rawlplugs.
We advise you to use the following type of rawlplug: "Steel anchor
bolts M8/diam. 14 for heavy duty use".
11
IMPORTANT REMARKS
Attention! Only for EU customers - WEEE marking.
This symbol indicates that once the products life-span has expired
it must be disposed of separately from other rubbish. The user
is therefore obliged to either take the product to a suitable dif-
ferential collection site for electronic and electrical goods or to
send it back to the manufacturer if the intention is to replace it
with a new equivalent version of the same product.
. NOT