Herunterladen Inhalt Inhalt Diese Seite drucken

Parkside PDKS 120 A2 Originalbetriebsanleitung Seite 51

Vorschau ausblenden Andere Handbücher für PDKS 120 A2:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 62
Anleitung_LB5_4309025:_
extension cable regularly and replace it if
damaged. Keep handles dry and free from
oil and grease.
14. Pull out the power plug
When tools are not in use, before starting
any maintenance work or when changing
attachments such as saw blades, drill bits
and all kinds of mounted tools.
15. Always remove keys and wrenches after
use
Always check that keys, wrenches and other
adjusting tools have been removed before
you switch on the equipment.
16. Avoid unintentional starting
Never carry a tool with your finger on the
switch button while the tool is connected to
the power supply. Make sure that the switch
is turned off when connecting the tool to the
power supply.
17. When using an extension cable
outdoors
Check that it is approved for outdoor duty
and is marked accordingly.
18. Be alert at all times
Watch what you are doing. Use common
sense when working. Never use the tool
when you are distracted.
19. Check your tool for damage
Before using the tool again, check the safety
devices or any slightly damaged parts to
ensure that they are in good working order.
Check that the moving parts are working
correctly, that they do not jam, and that no
parts are damaged. Make sure that all parts
are fitted correctly to ensure that the
equipment remains safe to use.
Unless otherwise stated in the operating
instructions, damaged guards and parts
have to be repaired or replaced by a
customer service workshop. Damaged
switches have to be replaced by a customer
service workshop. Never use an electric
power tool with a switch that cannot be
turned on and off.
20. Important.
For your own safety you must only use the
accessories and additional units listed in the
operating instructions or recommended or
specified by the manufacturer. The use of
mounted tools or accessories other than
25.05.2011
14:03 Uhr
Seite 51
those recommended in the operating
instructions or catalog may place your
personal safety at risk.
21. Repairs may only be carried out by a
qualified electrician
This electric power tool complies with the
pertinent safety information. Repair work
must only be carried out by a trained
electrician, otherwise the equipment may
cause accidents.
22. Connect up the dust extraction system
If there are provisions for connecting up a
dust extraction system, make sure that such
a system is fitted and in use.
Additional safety instructions
Switch the machine off immediately and pull
the power plug in an emergency.
Follow all these safety instructions before
and while working with the saw.
Do not use this saw to cut fire wood.
Do not use this saw to cross-cut roundwood
without a suitable holding device.
The machine is equipped with a safety
switch to prevent it from being switched on
again accidentally after a power failure.
If you need to use an extension cable, make
sure its conductor cross-section is big
enough for the saw's power consumption.
Minimum cross-section 1 mm
If you use a cable reel, the complete cable
must be pulled off the reel.
Persons working on the machine should not
be distracted.
After you have switched off the motor, never
slow down the saw blade by applying
pressure to its side.
Only fit blades which are well sharpened
and have no cracks or deformations.
Faulty saw blades must be replaced
immediately.
Never use saw blades which do not comply
with the data specified in this manual.
It is imperative to make sure that all devices
which cover the saw blade are in good
working order.
Never dismantle the machine's safety
devices or render them inoperative.
Damaged or faulty safety devices have to be
replaced immediately.
GB/
MT
2
.
51

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis