3M NANO-LOK 3500224 Benutzeranleitung Seite 8

This product is part of a personal fall arrest, work positioning, or rescue system. The user must follow
EN
the manufacturer's instructions for each component of the system. These instructions must be provided
to the user of this equipment. The user must read and understand these instructions before using
this equipment. Manufacturer's instructions must be followed for proper use and maintenance of this
equipment. Alterations or misuse of this product or failure to follow instructions may result in serious
injury or death.
If you have questions on the use, care, or suitability of this equipment for your application, contact
i
Capital Safety.
Before using this equipment, record the product identifi cation information from the ID label and iSafe RFID
i
tag in the inspection and maintenance log of this manual.
GLOSSARY REFERENCES
Numbered Glossary References on the front cover of this instruction reference the following items:
1
User Instructions.
2
Nano-Lok™ Self Retracting Lanyards.
3
Model Numbers: (See Figure 1).
DESCRIPTION:
Figure 1 illustrates Nano-Lok Edge™ Self Retracting Lanyard (SRL) models covered by this instruction manual:
Nano-Lok Edge cable lifeline SRLs in model groups
revision 6 Standard. (See Section 2.10)
i Cable Model 3500256 meets VG 11.060 Type A test requirements.
Nano-Lok Edge web lifeline SRLs in model groups
Type A Edge test requirements of the VG 11.60 revision 6 Standard. (See Section 2.10)
All Nano-Lok Edge SRL models are mounted just below the dorsal D-ring location of the user's full body harness. Models are
available in both single and twin SRL confi gurations which incorporate several snap hook, carabiner and WrapBax attachment
options. The SRLs include an integral energy absorber. The SRLs automatically lock at the onset of a fall to arrest the falling
worker, but pay out and retract during normal movement.
Figure 2 illustrates key components of Nano-Lok Edge SRLs:
G Harness Interface
H Housing
I Energy Absorber Cover
1.0 APPLICATIONS
1.1 PURPOSE: DBI/SALA Nano-Lok Edge SRLs with leading edge capability are designed for use in applications where
falls may occur, including falls over edges, such as roofi ng, leading edge construction, etc. SRLs are designed to be a
component in a personal fall arrest system (PFAS). SRLs may be used in many situations where a combination of worker
mobility and fall protection is required (i.e. inspection work, general construction, maintenance work, oil production,
confi ned space work, etc.). Twin Nano-Lok Edge models incorporate two SRL units that can be used for applications where
100% tie-off is required.
1.2 STANDARDS: Your Nano-Lok Edge SRL conforms to the CE standards identifi ed on the front cover of these instructions.
1.3 TRAINING: This equipment is intended to be used by persons trained in its correct application and use. It is the
responsibility of the user to assure they are familiar with these instructions and are trained in the correct care and use
of this equipment. Users must be aware of the operating characteristics, application limits, and the consequences of
improper use.
2.0 LIMITATIONS & REQUIREMENTS
Always consider the following limitations and requirements when installing or using this equipment:
2.1 CAPACITY: The DBI/SALA Nano-Lok SRL with Leading Edge capability is designed for use by one person with a combined
weight (person, clothing, tools, etc.) of up to 141 kg for all applications including Leading Edge.
At no time shall more than one person connect to a single SRL for fall arrest applications.
2.2 ARREST FORCE: SRLs documented in this instruction meet the following Arrest Force values:
Average Arresting Force
Maximum Arresting Force
2.3 ANCHORAGE: Anchorage structure for the SRL must be capable of supporting loads up to 12 kN. Anchor devices must
conform to EN795.
The anchor point must be located at the same height or above the edge over which a fall might occur.
Failure to heed this warning may result in equipment malfunction, serious injury, or death.
4 Standards.
5 Number of body that performed CE test.
6
Number of body checking the manufacture of this PPE.
A B
and meet the Type B Edge test requirements of the VG 11.54
C and D , and WrapBax™ SRLs in model groups
J Cable Lifeline M
K Cable Guide Bumper N
L Snap Hook O
4.0 kN
6.0 kN
8
iSafe™ RFID Tag P
Hook and Loop Straps Q
Web Lifeline R
E and F , meet the
WrapBax Lifeline Components
WrapBax Webbing
WrapBax Snap Hook