G Eneral Notes On Safety; Se Of The Machine For Purposes For Which It Is Intended; I Ncorrect Use; Ec Declaration Of Conformity - SUHNER ABRASIVE UBC 10-R Betriebsanleitung

1. n
1.1 g
enerAl notes on sAfety
This operation manual is applicable for the machine UBC
9-R. The machine may only be handled by personnel who
are qualified.
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may con-
tact hidden wiring or its own cord. Contact with a «live»
wire will make exposed metal parts of the tool «live» and
shock the operator.
WARNING Read all safety warnings and all in-
structions. Failure to follow the warnings and in-
structions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
1.2 u
se of the mAchine for purposes for
which it is intended
The machine is designed for grinding and polishing of
metal, plastic or wood with abrasive belts, non-woven
belts, high-performance ceramic belts or reinforced non-
woven belts, without using water. The machine is de-
signed exclusively for a 2-hand application.
1.3 i
ncorrect use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 ec
declArAtion of conformity
Otto Suhner GmbH of Trottäcker 50, D-79713 Bad Säck-
ingen, hereby declares under sole responsibility that the
product with the serial or batch no. (see reverse side) com-
plies with the requirements under the Directive 2014/30/
EU, 2006/42/EC, 2011/65/EU. Applied standards: EN ISO
12100, IEC 62841, EN 55014-1, EN 55014-2, EN 61000-3-
2, EN 61000-3-3. Document Agent: M. Voyame. D-Bad
Säckingen, 07/2018.
M. Voyame/Division manager
2. c
2.1 p
rior to tAKing the mAchine into serVice
Before connecting tool to a power
source, be sure the voltage sup-
plied is the same as specified on
the name plate of the tool.
Check the grinding belt before use. The driver roller must
be installed centrally and aligned to the stop. Under no
circumstances must the grinding belt exceed the max
permitted speed. Observe national regulations. Take pro-
24
S
oteS on afety
ommISSIonIng
tective measures when dust can develop during working
that is harmful to one's health, cumbustible or explosive.
Wear a dust mask and work with dust/chip extraction
when connectable.
2.2 t
AKing the mAchine into serVice
Select a speed from the table and set this for the grinding
belt at the setting wheel.
Level 1: 4.8m/s
Level 2: 6.5m/s
Level 3: 8.2m/s
Never raise the speed chosen for the belt when it
is running!
2.2.1 t /t
unr on urn off
The switch must be at the OFF position, i.e. the «0» is
visible. To switch ON the tool, press the switch, and push
it forwards until it engages audibly, i.e. the «1» becomes
bisible. Press the ON/OFF swith to trigger the blocking
and the machine shuts down.
2.3 r

Ating dAtA

Power voltage
Power Input
Power Output
Belt speed in idle
Lenght of the grinding belt
Width of the grinding belt
Grinding belt type
Thickness of the grinding belt
Sound pressure level IEC 62841
Noise emission level
Vibration IEC 62841
Level 4: 9.8m/s
Level 5: 11.5m/s
Level 6: 13.2m/s
120/230/240V, 50/60Hz
600W
300W
13.2m/s
520mm / 20 1/2"
3-19mm / 1/8"-3/4"
Nonwoven and grinding belts
max. 4mm
80dB(A), K=3dB(A)
91dB(A), K=3dB(A)
2
5.0m/s , K=1.5m/s
2