Warranty - Virutex SC134L Gebrauchsanweisung

connection and remove the brush. Replace the brushes
the other way around.
For model SC234L, loosen screws Q and remove lateral
covers R (Fig. 2). Proceed in the same way as for the
previous model.
14. GREASING
(to be performed by an official technician)
The screws on the gear head must not be loosened
during the warranty period. Otherwise the warranty
will be invalid.
The grease should be renewed after 1,500 hours of
use.
15. OPTIONAL ACCESSORIES
3445400 Lateral fence / compass
8200010/200 Dust collectors AS182K/AS282K
6446073 Dust collector attachment
1746245 Standard dust collector attachment 5 m
16. OPTIONAL JIG SAW BLADES
(Set of 5)
3440163 Pack of jig saw blades (carbon steel). For soft and
hard wood, veneer and chipboard of up to 80 mm.
3440164 Pack of jig saw blades (carbon steel). For soft
and hard wood, veneer and chipboard of up to 80 mm,
insulating fibres and flexible plastics.
3440165 Pack of jig saw blades (high speed steel).
For soft steel and iron of up to 5 mm, melamine and
synthetic fibres up to 8 mm and non-ferrous metals
up to 20 mm.
3440166 Pack of jig saw blades (high speed steel). For
soft steel and iron of up to 5 mm, non-ferrous metals
up to 20 mm and melamine and synthetic fibres up
to 10 mm.
3440167 Pack of jig saw blades (carbon steel). For soft
and hard wood and chipboard of up to 80 mm.
3440169 Blister pack of 3 assorted jig saw blades for
wood and metal.
17. NOISE AND VIBRATION LEVELS
The noise and vibration levels of this device have
been measured in accordance with European stan-
dard EN60745-2-11 and EN 60745-1 and serve as a
basis for comparison with other machines with similar
applications.
The indicated vibration level has been determined for
the device's main applications and may be used as an
initial value for evaluating the risk presented by expo-
sure to vibrations. However, vibrations may reach levels
that are quite different from the declared value under
other application conditions, with other tools or with
insufficient maintenance of the electrical device or its
accessories, reaching a much higher value as a result
of the work cycle or the manner in which the electrical
device is used.
Therefore, it is necessary to establish safety measures
to protect the user from the effects of vibrations, such
as maintaining both the device and its tools in perfect
condition and organising the duration of work cycles
(such as operating times when the machine is subjected
to loads, and operating times when working with no-load,
in effect, not in use, as reducing the latter may have a
considerable effect upon the overall exposure value).

18. WARRANTY

All VIRUTEX power tools are guaranteed for 12 months
from the date of purchase, excluding any damage which
is a result of incorrect use or of natural wear and tear
on the machine. All repairs should be carried out by the
official VIRUTEX technical assistance service.
VIRUTEX reserves the right to modify its products wi-
thout prior notice.
F R A N Ç A I S
SCIE SAUTEUSE SC134L/SC234L
(Voir images pages 23, 24, 25)
Important
Avant d'utiliser la machine, lisez attenti-
vement ce MANUEL D'INSTRUCTIONS et la
BROCHURE D'INSTRUCTIONS GÉNÉRALES
DE SÉCURITÉ qui vous sont fournis avec
cette machine. Assurez-vous de bien
avoir tout compris avant de commencer
à travailler sur la machine.
Gardez toujours ces deux manuels d'instructions à
portée de la main pour pouvoir les consulter, en cas
de besoin.
1. INSTRUCTIONS DE SÉCURITÉ
POUR LE MANIEMENT DE LA SCIE
Lire avec soin le prospectus concernant
LES INSTRUCTIONS GÉNÉRALES DE SÉ-
CURITÉ, fourni avec la documentation
de la machine.
1. Avant de brancher la machine, vérifiez que la tension
de l'alimentation correspondant à celle indiquée sur la
7