Setting The Color System - Pioneer PDA-5003 Bedienungsanleitung

Setting the COLOR SYSTEM

INPUT3 and INPUT4 are compatible with a number of TV
system formats used around the world, which are
automatically detected by this unit.
Normally [COLOR SYSTEM: AUTO] should be selected
for automatic detection. However, some video signals are
dubbed over or in certain conditions may not be displayed
properly (loss of color, etc.) by this setting. In this case,
change the setting according to the input signal.
Note
Setting the TV system format is required for each input (INPUT3
and INPUT4). Setting assignment and exclusive use according to
the TV system format of your input signal will enable prompt
processing of signals and reduction of time for input selection
and possible errors in detecting signals.
Remote control unit
DISPLAY
STANDBY/ON MENU
/ SET
MENU SET
Display operating panel
1
Press the MENU button to display the menu
screen.
M E N U
P I C T U R E S C R E E N
C O N T R A S T
B R I G H T N E S S
C O L O R
T I N T
S H A R P N E S S
P I C T U R E R E S E T
SET ENTER
MENU
2/3
SET
5/∞
INPUT SCREEN SIZE – VOL +
5/∞ 2/3
I N P U T 1
S E T U P O P T I O N
0
:
0
:
0
:
: 0
0
:
MENU EXIT
2 Use the 2/3 buttons to select [SETUP].
MENU
PICTURE SCREEN
C O L O R T E M P.
A U T O P O W E R O F F
D N R
M P E G N R
C T I
P U R E C I N E M A
C O L O R D E C O D I N G
C O L O R S Y S T E M
S I G N A L F O R M AT
SET CHANGE
3 Use the 5/∞ buttons to select [COLOR SYSTEM].
MENU
PICTURE SCREEN
C O L O R T E M P.
A U T O P O W E R O F F
D N R
M P E G N R
C T I
P U R E C I N E M A
C O L O R D E C O D I N G
C O L O R S Y S T E M
S I G N A L F O R M AT
SET
CHANGE
4
Press the SET button repeatedly until the
appropriate setting appears.
The factory default setting is [AUTO].
Each time SET button is pressed, the settings change
in the following order:
3 AUTO 3 NTSC
PAL N 2 PAL M 2
MENU
PICTURE SCREEN
C O L O R T E M P.
A U T O P O W E R O F F
D N R
M P E G N R
C T I
P U R E C I N E M A
C O L O R D E C O D I N G
C O L O R S Y S T E M
S I G N A L F O R M AT
SET
CHANGE
5
When the setup is finished, press the MENU
button to exit the menu screen.
Other Operations
INPUT1
SETUP OPTION
: M I D D L E
: D I S A B L E
: M I D D L E
: L O W
: O N
: O F F
: R G B
: A U T O
MENU EXIT
INPUT1
SETUP OPTION
: M I D D L E
: D I S A B L E
: M I D D L E
: L O W
: O N
: O F F
: R G B
: A U T O
MENU
EXIT
3 PAL 3 SECAM
4.43 NTSC 2
INPUT1
SETUP OPTION
: M I D D L E
: D I S A B L E
: M I D D L E
: L O W
: O N
: O F F
: R G B
: N T S C
MENU
EXIT
45
En