HEIDENHAIN ND 287 Kurzanleitung Seite 5

ND 287
Setup
For detailed description, see www.heidenhain.de
Before Switch-On
Electrical connection
Line voltage 100 - 240 Vac
Power frequency 50 - 60 Hz (± 2 Hz)
Power consumption † 30 W
Line fuse 2 x T500 mA
Wiring the power connector
L: Phase (brown)
N: Neutral (blue)
: Grounding conductor (yellow/green)
Caution: Changes to the power
cable may be made only by an
electrical technician.
Danger of electrical shock!
• Do not open the unit.
• The protective ground connection
must never be interrupted, not even if
a network adapter is used.
Danger to internal components
• Do not engage or disengage any
connecting elements while the unit is
under power.
• Use only original fuses.
Connections
1
Power switch
2
Power connection with fuse
3
Ground (protective ground)
X1
Encoder input for HEIDENHAIN
encoder with 11-µApp, 1-Vpp or
EnDat-2.2 interface
X2
Optional input: Input for encoder
module or analog module
X26
Optional interface: Installation of
Ethernet module (100BaseT)
X31
RS-232-C/V.24 interface
X32
USB Type B (UART) interface
X41
Switching inputs/outputs
Controls and Displays
1.
Position display
2.
Soft keys for functions
3.
Message line for displaying
information, error messages, and
information on samples or temperature
Confi rms an entry and returns
to the previous screen.
Deletes an entry, acknowledges
an error message, or returns
to the previous screen.
Moves through the soft-key
pages.
4.
Status bar
Operating mode: Actual Value
(active) – Distance-To-Go
(selectable by soft key)
Input: X1 (active), X2, X1 + X2,
X1 – X2, f(X1;X2) (selectable
by soft key if a module is
connected to the 2nd input)
Scale factor (inactive; can be
activated via Job Setup)
Error compensation (inactive;
can be activated via Installation
Setup)
Stopwatch (inactive; can be
activated via Job Setup)
Unit of measure: mm (active),
inch, DEG, DMS or rad
(selectable by soft key)
Datum point 1 (active) or 2
(selectable by soft key)
Soft-key page (page 1 active,
3 pages are available, use the
navigation key to move
through the pages)
5.
Status display
(greater than, within,
less than the tolerance limit)
active in sorting and tolerance
checking mode
(minimum,
actual, maximum measured
value, and difference between
MIN and MAX) if MEAS.
SERIES mode is active
(selectable by soft key)
Datum setting (fl ashes when a
value is entered)
Reference-mark evaluation
(active)
Very important
Please note
For your information
Initial Operation
The position display unit must be
set up properly during initial operation,
or when an encoder is exchanged.
Only this way the unit can be adapted
to the encoder requirements in order
to ensure that the movements are
displayed correctly.
Power Up
1.
Connect the components.
2.
Connect the ND to the network.
3.
Press the power switch to switch the
ND on. The initial screen appears:
4.
Select the language.
Press the soft key repeatedly until the
proper language appears. Press the
HELP soft key to call the integrated
help system in your language. The help
system provides support for all further
entries and functions.
Integrated Help System
Press the HELP soft key to call the
integrated help system. It provides
information and assistance (in the
language of your country) for the current
operation in any situation.
Press the LIST OF TOPICS soft key to
view information on any topic.
Use the PAGE UP/DOWN soft keys to
scroll one page up or down, and the
arrow keys to move one line up or
down. Press the C key to return to the
previous screen.
1