Service And Special Funtions; Software Upgrade; Initialization Of The Set; Service Menu - Grundig XENARO GDP 5100 Serviceanleitung

Xenaro – GDP 51..., GDP 6150
Service and Special Functions

Software Upgrade

Attention: if a failure should occur during the software upgrade
(e.g. a mains failure), it may happen that the units function and a
restart of the upgrade function are no longer possible. If this
should be the case, you must replace the integrated FLASH ICs
(U13 / U15) with preprogrammed ICs (see corresponding spare
parts list).
– Insert the upgrade CD (see corresponding spare parts list) and
observe the hints on the display and on the screen of the TV set.
– Carry out an initialization of the set.

Initialization of the Set

Press the 5 / 6 buttons on the set at the same time and connect the
set to the mains. This resets the software of the set to the factory
presettings. The basic settings are loaded and the customer-specific
data is cleared.

Service Menu

The Service menu is subdivided into the freely accessible "System
information" menu and the password-protected "Dealer service menu".
1. Functions of the buttons
For navigating in the Service menu, the buttons on the remote control
are used.
i
Call up the Player menu / End the menu functions.
S A
/ Select menu functions.
a
Select higher menu function.
s
Activate menu function / next diagnostic page.
OK
Activate menu function.
x
Select higher menu function.
1...9
Activate menu function directly.
Subtitle
Exit demo function.
2. Calling up the Service menu
– Call up the "Player Menu" using the »i« button.
– Select "Installation" using the 5 button,
S A
or use the / buttons and confirm with the »OK« button.
– Select "Additional functions" using the 5 button,
S A
or use the / buttons and confirm with the »OK« button.
– Select the "Service Menu" using the 3 button,
S A
or use the / buttons and confirm with the »OK« button.
The Service menu is subdivided in sub-menus according to the menu
overview (Point 3).
2.1 System information
– Call up the "Service menu" (Point 2).
– Select "System information" using the 1 button,
S A
or use the / buttons and confirm with the »OK« button.
The System information menu appears on the picture screen.
System information
GDP 6150
Unit
SW-Version: 1.00 / 249
Software version
HW-Version: 0.03
Hardware version
Copyright: GRUNDIG AG 2001
Hardware information
http://www.grundig.com
NDV8501/DVD-2/Pantera-II rev 2 R:2
Regional code
select
and choose
2.2 Retailer service menu
– Call up the "Service menu" (Point 2).
– Call up the "Retailer Service" menu using the 2 button,
S A
or use the / buttons and confirm with the »OK« button.
– Enter the digits "8 5 0 0".
Note: the further menus can be called up according to the menu
overview (Point 3).
GRUNDIG Service
2.2.1 System settings
– System messages
– Diagnostic
– Demo
2.2.4 Video special
– Format conversion
– Video signal
exit
back
Service- und Sonder-Funktionen / Service and Special Functions
When selecting a function or in the case of an error (e.g. disc,
handling or unit error), the system emits messages which are briefly
displayed in the bottom area of the picture screen.
The diagnostic functions are subdivided on several pages.
To select the desired page, enter its number (e.g. 2 for State) then
confirm with »OK«.
In diagnostic mode, the following functions are possible:
s
– Use the button to select the next diagnostic page or to end the
diagnostic mode after the last page.
– Use the »i« to exit the diagnostic mode early.
The following diagnostic pages can be called up:
(1) Brief Disc and player state
(2) State Player state and error
(3) Tray Tray information
(4) Disc Disc information
(5) DVD DVD information
(6) DVD-V DVD video information
(7) DVD-A DVD audio information
(8) VCD VCD information
(9) CD Audio CD information
(10) File MP3 state
(11) File Info MP3 information
(12) Video Video state
(13) Aud 1 Audio information, page 1
(14) Aud 2 Audio information, page 2
(15) SP Subpicture information
(16) Angle Viewing angle information
(17) Title Titel information
(18) Track Track information
(19) Chptr Chapter information
(20) Index Index state
(21) Group DVD audio group information
(22) Dlist DVD audio ASVU list
(23) Repeat Repeat state
(24) Btns Buttons information
(25) Spd Playing speed
(26) Bitrt Bitrate
When the demo function is activated, the eject button and the on/off
switch are locked.
Ending the demo function: press the »Subtitle« button.
The following format conversions are possible:
– Centre
– Auto
– 525 lines only
– 625 lines only
• DAC enable
The following digital-to-analog converters can be activated/deac-
tivated:
– DAC1 = Green/Y signal
– DAC2 = Blue/C signal
– DAC3 = Red signal (indication of the active switching state)
• NTSC format (60Hz format)
The following 60Hz formats can be selected:
– 525 lines, NTSC standard
– 525 lines, M-PAL standard
• NTSC composite signal
The following NTSC composite signal formats can be selected:
– NTSC USA
– NTSC Japan
– NTSC Other
• PAL format
The following PAL formats can be selected:
– PAL BDGHI
– PAL N
– PAL N-Combo
2 - 3