Adjusting The Cutting Angle - Bosch GTS 10 XC Professional Originalbetriebsanleitung

OBJ_BUCH-1375-005.book Page 37 Friday, March 16, 2018 9:47 AM
– Keep the spindle lock lever pulled and unscrew the clamp-
ing nut turning in anticlockwise direction.
– Remove the clamping flange 58.
– Remove the saw blade 32.
Mounting the Saw Blade
If required, clean all parts to be mounted prior to assembly.
– Place the new saw blade onto the supporting flange 59 of
the tool spindle 60.
Note: Do not use saw blades that are too small. The clearance
between saw blade and riving knife must not exceed 5 mm
(max.).
 When mounting the saw blade, pay attention that the
cutting direction of the teeth (arrow direction on the
saw blade) corresponds with the direction of the arrow
on the blade guard!
– Mount the clamping flange 58 and the clamping nut 56.
– Turn the clamping nut 56 with the ring spanner 15
(24 mm) and at the same time, pull the spindle lock lever
57 until it engages.
– Tighten the clamping nut in clockwise direction.
(Tightening torque approx. 15–23 Nm)
– Reinsert the insert plate 31.
– Tilt blade guard 5.x down again.
Operation
 Before any work on the machine itself, pull the mains
plug.
Transport and Working Position of the Saw Blade
Transport Position
– Turn the handwheel 19 in anticlockwise direction until the
teeth of the saw blade 32 are positioned below the saw ta-
ble 17.
For additional information on transport, see page 40.
Working Position
– Turn the crank 20 clockwise, until the teeth of the saw
blade 32 are positioned above the workpiece.
Note: Take care that the blade guard is properly positioned.
When sawing, it must always face against the workpiece.
Increasing the Size of the Saw Table
Long workpieces must be underlaid or supported at their free
end.
Table Width Enlargement (see figure A)
The table width enlargement 11 enlarges the saw table 17 to-
ward the right by 435 mm (max.).
– Completely pull the clamping handle 18 for the table width
enlargement upward.
– Pull out the table width enlargement 11 to the desired
length (also see "Adjusting the Parallel Guide With the Saw
Table Extended", page 38).
– Press clamping handle 18 downward.
The table width enlargement is now locked.
Bosch Power Tools
Table Extension (see figure B)
The table extension 10 extends saw table 17 to the rear by
520 mm (max.).
– Loosen the locking screws 38 on the guide rods 24.
– Pull out the table extension 10 to the desired length.
– To lock the position, firmly tighten both locking screws 38.
For heavy workpieces, it may be required to support the table
extension.
Sliding Table (see figure C)
With the sliding table 2, workpieces to a maximum width of
350 mm can be sawn.
At the same time, a higher precision is achieved during saw-
ing, especially in conjunction with the angle stop 3. (see
"Sawing Mitre Angles with the Sliding Table", page 39)
– Completely pull the clamping lever 29 for the sliding table
upward.
In this manner, the sliding table can be moved both toward
the front as well as toward the rear to the stop.

Adjusting the Cutting Angle

To ensure precise cuts, the basic adjustment of the machine
must be checked and adjusted as necessary after intensive
use (see "Checking and Adjusting the Basic Adjustment",
page 39).
Adjusting Bevel Angles (Saw Blade)
(see figure D)
The bevel angle can be set in a range from –1° to +47°.
– Loosen the clamping lever 26 in an anti-clockwise direc-
tion.
Note: By completely loosening the locking knob, the saw
blade tilts approx. to the 30° position by means of gravity
force.
– Push or pull handwheel 19 alongside the connecting link
until the angle indicator 61 indicates the desired bevel an-
gle.
– Hold the handwheel in this position and tighten locking le-
ver 26 again.
For quick and precise setting of the standard 0° and 45°
angles, factory-set stops have been provided for.
Adjusting Mitre Angles (Angle Stop)
(see figure E)
The mitre angle can be set in the range from 60° (left side) to
60° (right side).
– Loosen the locking knob 62 in case it is tightened.
– Turn the angle stop until the angle indicator 63 indicates
the requested mitre angle.
– Tighten the locking knob 62 again.
For quick and precise setting of frequently used mitre an-
gles, stop screw for the 45° angles (left and right) and 0°
have been provided for on angle stop 3.
– Loosen the locking knob 62 in case it is tightened.
– Tilt the adjustment piece 80 outward.
– Turn the angle stop in such a manner that the thread of the
desired stop screw is positioned rightward to the adjust-
ment piece.
English | 37
1 609 92A 467 | (16.3.18)