Specifications; Specific Safety Rules - Makita 5705R Betriebsanleitung

ENGLISH
1 Hex wrench
2 Shaft lock
3 Tighten
4 Loosen
5 Saw blade
6 Outer flange
7 Inner flange
8 Outer flange
9 Hex socket head bolt
10 Saw blade

SPECIFICATIONS

Model
Blade diameter ............................................................................ 165 mm
Max. cutting depth
At 90° ........................................................................................ 54 mm
At 45° ........................................................................................ 38 mm
–1
No load speed (min ) ................................................................. 5,000
Overall length .............................................................................. 330 mm
Net weight ................................................................................... 4.2 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For model 5705R, public low-voltage distribution sys-
tems of between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.36 Ohms it can be presumed that
there will be no negative effects.
The mains socket used for this device must be protected
with a fuse or protective circuit breaker having slow trip-
ping characteristics.
Safety hints
For your own safety, please refer to the enclosed Safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to circular saw safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
Danger:
1. Keep hands away from cutting area and the
blade. Keep your second hand on auxiliary han-
dle, or motor housing. If both hands are holding
the saw, they cannot be cut by the blade.
4
Explanation of general view
11 Setting protuberances
12 Hex socket head bolt
(For adjusting riving knife)
13 Cutting depth
14 Loosen
15 Lever
16 Thumb nut
17 For 45° bevel cuts
18 For straight cuts
19 Base plate
2.
3.
4.
A typical illustration of proper hand support, work-
piece support, and supply cord routing (if applicable).
GEB029-1
5.
6.
20 45° angle cuts
21 Straight cuts
22 Top guide
23 Base
24 Lock-off button
25 Switch trigger
26 Vacuum cleaner
27 Limit mark
28 Brush holder cap
29 Screwdriver
5603R 5705R
190 mm
66 mm
46 mm
4,800
356 mm
5.2 kg
Do not reach underneath the workpiece. The
guard cannot protect you from the blade below the
workpiece. Do not attempt to remove cut material
when blade is moving.
CAUTION: Blades coast after turn off. Wait until
blade stops before grasping cut material.
Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
Never hold piece being cut in your hands or
across your leg. Secure the workpiece to stable
platform. It is important to support the work properly
to minimize body exposure, blade binding, or loss of
control. (Fig. A)
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will also make exposed
metal parts of the power tool "live" and shock the
operator.
When ripping always use a rip fence or straight
edge guide. This improves the accuracy cut and
reduces the chance of blade binding.
5903R
235 mm
85 mm
64 mm
4,500
400 mm
7.0 kg
Fig. A