RIB TOUCH Wi-Fi Bedienungsanleitung Seite 19

TO MEMORIZE OTHER TOUCH Wi-Fi
- Press the PROG. TX key of the TOUCH Wi-Fi with microswitch 2 turned ON => on MASTER
Wi-Fi the bicolor EDGE PHOT 2 LED turns from flashing red to flashing green and a buzzer
tone sounds to indicate proper memorization of the TOUCH Wi-Fi .
- Perform the same procedure for any other TOUCH Wi-Fi (up to a maximum of 6).
CHECKING PROPER FUNCTIONING
After the memorization procedure, check proper functioning between the TOUCH Wi-Fi and
the MASTER Wi-Fi as follows:
- Make sure that when you press the TOUCH Wi-Fi strip with dip 1 ON, the corresponding
bicolor EDGE PHOT 1 LED on the MASTER Wi-Fi Board turns red for the duration of the
pressing action.
IN CASES OF DIFFICULTY
The strip does not work
FOR OTHER INFORMATION REFER TO THE INSTRUCTION BOOKLET OF THE MASTER Wi-Fi CARD
ELECTRONIC TECHNICAL CHARACTERISTICS
FREQUENCY
SENSITIVITY
OUTPUT POWER
POWER SUPPLY
INPUT AT REST
MAXIMUM INPUT
MODULATION TYPE
CAPACITY
BATTERY LIFE
CAPACITY OF CONTACTS
WORKING TEMPERATURE
DEGREE OF PROTECTION
DEGREE OF RELATIVE HUMIDITY
TECHNICAL MECHANICAL CHARACTERISTICS
STROKE FROM CONTACT TO INTERVENTION (PRE-STROKE)
STROKE FROM INTERVENTION TO MECHANICAL STRIKER PLATE (BEYOND STROKE)
OPENING TIME OF CONTACTS AFTER INTERVENTION
RECOVERY TIME OF MAXIMUM DEFORMATION
MAXIMUM FORCE APPLICABLE TO THE DEVICE
MAXIMUM SPEED OF DEVICE IN MOTION
*
Using with operators at a speed greater than 0.25 m/s (15 m/min) is a breach of regulatory provisions.
ROUTINE MAINTENANCE
ACCESSORIES
AA ALKALINE BATTERIES
4 X 1,5V - battery life with TOUCH Wi-Fi 3 years.
PROBLEM
868,3 MHz
-108 dBm
<25 mW
3 type AA batteries 1.5 V (> 2.7 Ah)
25 µA
13 mA
FSK
20 m in free space without antenna
3 years (type AA)
0,5 A - 24 V c.a. c.c.
-20°C ÷ +60°C
IP44
<93%
max 15 mm
min. 40 mm
max 0.1 s
max 0.5 S
max 1 KN
max 0.25 M/S *
code ACG9519
The DL2 LED will turn off to indicate interruption of the contact dedicated to the EDGE input
on the motor control panel.
- Repeat the check on all the installed TOUCH Wi-Fi.
Run a functional check on all the installed TOUCH Wi-Fi by activating the motion of the
automation and check that, upon collision with the strip, the automation stops/inverts its
motion.
Check condition of batteries and contact
Must be carried out every six months, only by authorized personnel in agreement with the
safety rules and with the manufacturer's instructions.
- The TOUCH Wi-Fi safety edge must be kept in efficient working conditions and in
agreement with the manufacturer's instructions.
- Replace the batteries when requested by the system (see the chart "IN CASE OF
DIFFICULTIES" on the MASTER Wi-Fi manual).
- Verify the presence and the possibility to read the initial marking.
- The parts that wear off are mentioned in the chart "Type of items for the assembly";
eventual replacements must be carried out by an authorized technician, following the
assembly instructions and verification.
1 - Make sure covers (upper and lower ) and aluminum support are in good condition and not
bent out of shape; make sure rubber part is in good condition and not torn.
2 - Dismantle cover.
3 - Check steel cable to make sure it is in good condition and not frayed; replace cable is
necessary.
4 - Make sure that in conditions of rest, the lever is positioned on the central limit switch. If
it is not, regulate the position by turning the adjustment screws.
5 - Check condition of upper cover and replace it if it is damaged.
6 - Make sure there are no traces of moisture or foreign bodies and remove them if there
are any.
7 - Keeping the contact of the central limit switch pressed, press the rubber and make sure
the electric circuit is interrupted.
8 - Release rubber strip and make sure electric contact resets.
9 - Put cover back on.
AA LITHIO BATTERIES
2 X 1,5V - battery life with TOUCH Wi-Fi 4 years (buy 2 pieces).
For extreme temperatures -40÷+60°C.
19
CHECK
code ACG9509
G
B