voestalpine Böhler Welding URANOS 2700 SMC Betriebsanweisung Seite 37

15 Burn back
Permits adjustment of the wire burn time, preventing
sticking at the end of welding.
Permits adjustment of the length.
Permits adjustment of the length of the piece of wire
outside the torch.
Minimum -2.00, Maximum +2.00, Default syn
16 Post-gas
Permits setting and adjustment of the gas flow at the
end of welding.
Minimum off, Maximum 10 sec., Default 2 sec.
30 Spot welding
Allows you to enable the "spot welding" process and
establish the welding time.
Minimum 0.1s, Maximum 25s, Default off
31 Pause point
Allows you to enable the "pause point" process and
establish the pause time between one welding opera-
tion and another.
Minimum 0.1s, Maximum 25s, Default off
202 Inductance
Allows electronic regulation of the series inductance of
the welding circuit.
Makes it possible to obtain a quicker or slower arc to
compensate for the welder's movements and for the
natural welding instability.
Low inductance = reactive arc (more spatter).
High inductance = less reactive arc (less spatter).
Minimum -30, Maximum +30, Default syn
500 Reset XE (Easy Mode)
Not used
Reset XA (Advanced Mode)
Manual welding method.
Allows the manual setting and regulation of each indi-
vidual welding parameter.
Reset XP (Professional Mode)
Allows the manual setting and regulation of each indi-
vidual welding parameter.
Makes it possible to use a series of pre-settings available
in the memory of the system.
Allows access to the higher set-up levels:
USER: user
SERV: service
vaBW: vaBW
551 Lock/unlock
Allows the locking of the panel controls and the inser-
tion of a protection code (consult the "Lock/unlock"
section).
601 Regulation step
Allows the regulation of a parameter with a step that can
be personalised by the operator.
Minimum 1, Maximum Imax, Default 1
602 External parameter CH1
Allows the management of external parameter 1 (mini-
mum value).
603 External parameter CH1
Allows the management of external parameter 1 (maxi-
mum value).
604 External parameter CH2
Allows the management of external parameter 2 (maxi-
mum value).
605 External parameter CH2
Allows the management of external parameter 2 (maxi-
mum value).
705 Circuit resistance calibration
Lets you calibrate the system.
Press the encoder knob to access parameter 705.
Place the tip of the wire guide in electrical contact with
the work piece.
Press and hold the torch trigger for at least 1 s.
707 Motor calibration
Consult the "Motor calibration" section.
751 Current reading
Allow the real value of the welding current to be dis-
played.
Allows the welding current display method to be set.
752 Voltage reading
Allows the real value of the welding voltage to be dis-
played.
Allows the welding voltage display method to be set.
757 Wire speed reading
Allow the value of the motor encoder 1 to be displayed.
760 (Motor) Current reading
Allow the real value of the (motor) current to be dis-
played.
852 TIG DC LIFT START enabling
On=Active, Off=No active
3.3.3 List of set up parameters (MIG/MAG)
(URANOS...smart)
0 Save and quit
Allows you to save the changes and exit the set up.
1 Reset
Allows you to reset all the parameters to the default
values.
3 Wire speed
Allows the regulation of the wire feed rate.
Minimum 0.5 m/min, Maximum 22 m/min, Default
1.0m/min
4 Current
Allows the regulation of the welding current.
Minimum 6A, Maximum Imax
5 Part thickness
Allows the thickness of the part being welded to be set.
Allows the setting of the system via the regulation of the
part being welded.
6 Corner bead
Lets you set bead depth in a corner joint.
7 Voltage
Allows the regulation of the arc voltage.
Allows regulation of the arc length during welding.
Manual MIG/MAG:
High voltage = long arc
Low voltage = short arc
Minimum 5V, Maximum 55.5V
Synergic MIG/MAG:
Minimum 5V, Maximum 55.5V, Default syn
10 Pre-gas
Allows you to set and adjust the gas flow prior to striking
of the arc.
Permits filling of the torch with gas and preparation of
the environment for welding.
Minimum off, Maximum 25 sec., Default 0.1 sec.
37