Before Starting The Machine; Setting The Cutting Height; Fuel And Oil - EINHELL BG-PT 3041 Bedienungsanleitung

Anleitung_BG_PT_3041_SPK1:_
GB
Cutting line diameter:
Tank capacity
Spark plug
Vibration a
hv
Idling speed (max.)
Idling speed (max.)
L sound pressure level
pA
L sound power level
WA
Sound and vibration were measured in accordance
with DIN EN 11806.

5. Before starting the machine

5.1 Montage
Assembling the long handle (Fig. D1 – D3)
Slacken the star grip screw (Fig. D1/Item 1) on the
connecting piece on the upper long handle (Fig.
D1/Item 3). Then press the lever catch (Fig. D1/Item
2) and carefully slide the lower long handle (Fig.
D1/Item 4) into the connecting piece on the upper
long handle. When doing so, take care to ensure that
the drive shafts on the insides of the long handles
slide into each other (turn the spool head gently, if
required) and that the front lug on the lever catch (Fig.
D2/Item 6) locks into the corresponding hole in the
lower long handle (Fig. D2/Item 5). Then retighten the
star grip screw (Fig. D1/Item 1) (Fig. D3). To
dismantle, proceed in reverse order.
Fitting the additional handle (Fig. E1 – E3)
Slacken the wing nut on the fastening screw on the
handle (Fig. E1/Item 1). Remove the wing nut, washer
(Fig. E1/Item 2) and fastening screw (Fig. E1/Item 3)
from the handle and insert them in the long handle
(Fig. E2). Then screw the handle to the long handle
(Fig. E3).
Fitting the guard hood (Fig. F1 – F3)
Slacken the fastening screw on the guard hood (Fig.
F1/Item 1) with the help of the Allen key provided and
then remove (Fig. F1). Then attach the guard hood to
the lower long handle (Fig. F2). Screw the guard hood
tightly in position with the fastening screw (Fig. F3).
Fitting the carrying strap (Fig. G)
The carrying strap is intended to help you work safely
and ergonomically with the power trimmer. Hook the
carrying strap into the fastening eyelet (Fig. G/ Item
A).
18
17.06.2008 11:02 Uhr
2.0 mm Check that all moving parts move smoothly
before you start using the machine. Check that
0.8 l
all screws are securely fastened and also check
Champion RCJ6Y
all the safety devices.

5.2 Setting the cutting height

5.8 m/s 2
Slip the shoulder strap (Fig. A/17) over the left
7.9 m/s 2
shoulder.
Set the length of the shoulder strap in such a way
100 dB (A)
that the cutting head runs parallel to the ground.
108 dB (A)
In order to establish the optimum length of the
shoulder strap, you should then make a few
swinging movements without starting the engine
(Fig. I).
Please note: Always use the shoulder strap when
using the appliance. Attach the strap as soon as you
have started the engine and the engine is running in
idle mode. Switch off the engine before you take off
the shoulder strap.
Check the machine for the following each time before
use:
That there are no leaks in the fuel system
That the cutting unit and all safety devices are in
perfect condition
That all screws are securely fastened

5.2 Fuel and oil

Recommended fuels
Use only a mixture of normal unleaded petrol and
special 2-stroke engine oil. Mix the fuel mixture as
indicated on the fuel mixing table.
Please note: Do not use a fuel mixture which has
been kept for longer than 90 days.
Please note: Do not use 2-stroke oil with a
recommended mixing ration of 100:1. If inadequate
lubrication causes engine damage, the
manufacturer's engine warranty will be voided.
Please note: Only use containers designed and
approved for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke oil
into the mixing bottle (see scale printed on the bottle).
Then shake the bottle well.
5.3 Fuel mixture table
Mixing procedure: 40 parts petrol to 1 part oil
1 liters
2 liters
Seite 18
Petrol 2-stroke oil
25 ml
125 ml