Before Starting The Equipment - EINHELL AGILLO 36/255 BL Originalbetriebsanleitung

Uncertainty K ........................................ 3 dB (A)
Important!
The equipment is supplied without batteries and
without a charger and is allowed to be used only
with the lithium-ion batteries (two batteries) of the
Power X-Change series!
The lithium-ion batteries of the Power X-Change
series are allowed to be charged only with the
Power-X charger.
The machine noise might exceed 85 dB (A). The
operator will require noise protection measures
if this is the case. The noise is measured in ac-
cordance with ISO 22868. The value of the vib-
rations emitted by the handle was determined in
accordance with ISO 22867.
Important!
The vibration value changes according to the
area of application of the electric equipment and
may exceed the specifi ed value in exceptional
circumstances.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
•
Wear eye and hearing protection

5. Before starting the equipment

The equipment is supplied without batteries
and without a charger!
Caution! Carry out all the following assembly and
adjustment work without rechargeable batteries
–risk of injury. Wear protective gloves.
5.1 Fitting the guard hood (Fig. 3)
Remove the socket head screw from the guard
hood. Push the guard hood (15) onto the mount
on the motor housing as far as it will go and screw
it securely in place with the previously removed
socket head screw (Fig. 3). A blade (Fig. 2/ Item
Anl_Agillo_36_255_BL_SPK9-1.indb 26 Anl_Agillo_36_255_BL_SPK9-1.indb 26
GB
14) on the underside of the guard hood automa-
tically cuts the cutting line to the optimum length.
This is provided with a safety guard. Remove the
safety guard before starting work.
5.2 Fitting the additional handle (Fig. 4 – 4d)
Undo the handle screw (Fig. 2/Item 17) and remo-
ve the thrust piece (Fig. 2/Item 5). Fit the additio-
nal handle (16) into the holder (A) such that the
plastic ring (B) lies in the groove (N) on the holder
(A) (see detailed drawing 4a).
Caution! The additional handle is wrongly fi tted
if the plastic ring (B) lies outside the groove (N)
as shown in the detailed drawing 4b. This mistake
can result in damage to the additional handle
during use.
Fasten the additional handle (16) to the thrust
piece (5) by re-tightening the handle screw (17).
Use the two supplied cable clips (26) to fasten the
protective tubing for the cable.
5.3 Fitting the long handle (Fig. 5)
Slot the top part of the long handle (6) into the
bottom part of the long handle (9). Screw the
handle connecting piece (7) to the top part of the
long handle with the union nut (8) on the bottom
part of the long handle.
5.4 Adjusting the angle of the additional
handle (Fig. 4c)
To adjust the additional handle to the optimum
working angle, slacken the handle screw (17). Set
the desired tilt of the additional handle (16). Tigh-
ten the handle screw (17) again.
5.5 Removing/fi tting the cutting line unit
(Fig. 6)
Note: The equipment is supplied from the factory
ready for operation with the cutting line.
Warning! Take care not to cut yourself on the
cutting line cutter.
a) Removing the cutting line unit
Press the locking lever (12) forward and turn
the cutting line unit (C) clockwise (a) at the
same time until the locking lever latches in
place. Turn the cutting line unit clockwise (a)
and take it off the motor shaft.
b) Fitting the cutting line unit
Press the locking lever (12) forward and turn
the cutting line unit (C) counterclockwise (b)
onto the motor shaft at the same time until
the locking lever latches in place. Turn the line
cutting unit on the motor shaft until it is tightly
secured. Check whether the cutting line unit
can rotate freely after you let go of the locking
- 26 -
05.05.2020 10:55:34 05.05.2020 10:55:34