Werbung
© BOSTITCH 2019
UTILITY HOOK (Fig 3)
These tools include an additional utility hook suitable for
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
storage and temporary hanging of the tool.
compliance for the products.
m WARNING! Never use the utility hook to hang the tool
from the body, clothing or belt.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
m WARNING! Never use the utility hook with contact
rien que les produits soient conformes aux normes CE.
(black) trigger operated tools.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
die CE-Richtlinien für Produkte.
LOADING THE TOOL
1. Open the magazine: Pull pusher back to engage
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
latch. (Fig 4)
zeggen dat de producten voldoen aan de CE-vereisten.
2. Hold nailer down with magazine tilted downwards.
Insert sticks of nails. (Fig 5)
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
3. Close magazine: Release pusher by first puling back on
produkterne.
the pusher and then pressing the release tab.
Slide pusher against the nails. (Fig 6)
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
Note: Use only fasteners recommended by
yhdenmukaisuutta.
Bostitch for use in Bostitch tools or nails which
meet Bostitch specifications.
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα
αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
REMOVING NAILS (Fig 7)
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
1. Disconnect the tool from the air supply
2. Pull pusher back until it is securely engaged
conformità CE per i relativi prodotti.
3. Slide nails back to opening and push out
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for
CAUTION: The pusher and pusher spring
CE-merking for produktet.
(constant force spring).
Caution must be used when removing nails, as if pusher is
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
disengaged from latch it could spring forward potentially
conformidade com a CE para os produtos.
pinching your hand.
Extra caution should be taken when carrying out
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
maintenance on the magazine area of the tool. The spring is
wrapped around but not attached to a roller. If the spring is
conformidad con las normas CE de los productos.
stretched beyond its length, the end will come off the roller
and the spring will roll up with a snap, with a chance of
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
pinching your hand. Also the edges of the spring are very
conformidad con las normas CE de los productos.
thin and could cut your hand. Care must also be taken to
nsure no permanent kinks are put in the springs as this will
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
reduce the springs force.
nie stanowią deklaracji zgodności CE prezentowanych produktów.
GUIDE ROD INSTALLATION AND REMOVAL -
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
F21PL, F33PT, F33PTSM, N89RH17-2
nie stanowią deklaracji zgodności CE prezentowanych produktów.
Step 1 (Fig 8): Locate guide (A); Pull and rotate cover (B).
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
Step 2 (Fig 9): Locate access windows foe installation
and removal of guide rod (C); Locate guide rod storage
výrobky.
channel (D); Rotate cover open to install or remove guide
rod (E); Install or remove guide rod through rear of
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem
magazine (F).
jelenti a termék CE-megfelelőségét.
Step 3 (Fig 10): Install guide rod through (G) for 2.8mm to
3.3mm shank nails. Rotate cover (B) to close; Install guide
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
rod through (H) for 3.3mm to 4.1mm shank nails. Rotate
conformitatea CE pentru produse.
cover (B) to close.
DRIVER MAINTENANCE INSTRUCTIONS
Worn driver causing poor quality or loss of power:
• Wear on the driving tip will affect the nail drive, giving
symptoms of bent and incompletely driven nails, and
damaged nail heads
• The driver length may be adjusted to allow the driving tip
to be redressed to compensate for wear. Heat and
precise measurement are required. Contact a qualified
service technician for this adjustment.
Note: Driver wear of approximately 3mm can be tolerated
in most applications. However, in difficult driving
applications, driver wear of approximately 1.5 mm may
cause a slight reduction in the apparent driving power.
GB
Werbung
