Verarbeitung und eine tigen HELIX Verstärkers. überzeugende Anwendung ausgereifter Technolo- gien aus. Audiotec Fischer setzt mit der HELIX D ONE neue Viel Freude an diesem Produkt wünscht Ihnen das Maßstäbe in puncto Preis-Leistungsverhältnis. Dabei profitieren Sie als Kunde direkt von unserer Team von mehr als 30-jährigen Erfahrung in der Forschung...
50 Hz bis 250 Hz. lichkeit des Line und Highlevel Inputs. Master / Slave Modus Phase Shift Schalter um zwei D ONE Verstärker im Regler zum Einstellen der Phase von 0° bis Brüc kenbetrieb zu betreiben. 180°. Mono Cinch In-/Output Bass Boost Mono Cinch Signalein- oder -ausgang für den...
Seite 4
Inbetriebnahme und Funktionen 1 Line Input 4 Phase Shift 2-Kanal Vorverstärkereingang zum Anschluss von Mit Hilfe dieses Reglers kann die Phase von 0° bis Signalquellen, wie z.B. Radios, die mit dem/den 180° eingestellt werden. Dies ermöglicht eine bes- Vorverstärkerausgang/-ausgängen bzw. Line Out- sere Ankopplung des Subwoofers an die Tieftonwie- puts der Signalquelle verbunden werden können.
Seite 5
Übertemperatur. Sollte sich der Verstärker 9 Master / Slave Modus nach Beseitigung der Fehlerquelle nicht Bei der D ONE handelt es sich um einen „real- wieder einschalten lassen, liegt ein Defekt mono“ Verstärker, der sich über den Master / Slave vor.
Eingang muss nicht belegt werden, wenn der ne Querschnitt beträgt mindestens 10 mm². Einbau und Installation Die HELIX D ONE wird wie nachfolgend be- Achten Sie bitte auf eine korrekte Polung! schrieben an das Autoradio angeschlossen. Wenn Sie einen Anschluss verpolen, kann da- durch die Funktion des Verstärkers beeinträch-...
Seite 7
Schalter auf „Master“ stellen (siehe Seite 5, Punk 9; Master / Slave Modus). maximalen Stromaufnahme der gesamten Car- Hifi Anlage (D ONE = max. 60 A RMS bei 12 V 2. Stellen sie den Master / Slave Modus Schal- Bordnetz).
Seite 8
Konfigurationsbeispiele Parallelbetrieb Zwei Subwoofer mit einer Schwingspule (Single Voice Coil) oder ein Subwoofer mit Doppelschwingspule (Dual Voice Coil) werden parallel geschaltet. Hinweis: Die Parallelschaltung von zwei Schwingspulen führt zur Halbierung der Impedanz! Maximale Ausgangsleistung dieser Konfiguration: Zwei Subwoofer mit 1 x 4 Ohm entsprechen einer Zwei Subwoofer mit einer Schwingspule Gesamtimpedanz von 2 Ohm: 340 / 680 Watt...
Konfigurationsbeispiele für den Master / Slave Modus Verstärkeranschluss im Master / Slave Modus Master Slave Signal vom Radio Schalterstellung: Schalterstellung: (Cinch oder Highlevel) Master Slave Cinchkabel Lautsprecheranschluss im Master / Slave Modus Master Slave Ein Subwoofer mit einer Schwingspule (Single Voice Coil) Maximale Ausgangsleistung dieser Konfiguration: 1 x 4 Ohm: 645 / 1.290 Watt 1 x 2 Ohm: 910 / 1.820 Watt...
HELIX dealer. cross-section for the connection of the HELIX Install your D ONE in a dry location with sufficient D ONE. The fuses may only be replaced by iden- air circulation for proper cooling of the equipment.
Seite 12
Control for adjusting the input sensitivity of 50 to 250 Hz. the lowlevel Line and Highlevel Inputs. Master / Slave Mode Phase Shift Switch for operating two D ONE amplifiers in Control for adjusting the phase from 0° to bridge mode. 180°. Mono RCA/Cinch In-/Output...
Seite 13
Initial start-up and functions 1 Line Input phase shifts. 2-channel lowlevel line input to connect signal sourc es such as head units / radios / DSPs. Important: It is strictly forbidden to use the High- level Input and lowlevel Line Input at the same time. This may cause severe damage to the lowlevel line outputs of your head unit / car radio.
The HELIX D ONE amplifier is a “real-mono” ampli- The input fuses are connected in parallel and pro- fier and can be connected to a second D ONE via vide protection against an internal fault of the de- the Master / Slave Mode by which the output power...
(this is located where ommended cross section: min. 10 mm² / AWG 8. Installation Connection of HELIX D ONE to the head unit / car radio: 3. Adjustment of the input sensitivity Attention: It is mandatory to properly adapt...
Seite 16
(optional) Never connect any of the loudspeaker cables to the chassis ground as this will damage your For connecting a further D ONE amplifier in bridge mode follow the subsequent steps: amplifier and your speakers. 1. Define the amplifier which is connected to the If you connect two loudspeakers in parallel signal source (radio) as “Master”...
Seite 17
Parallel operation Two subwoofers with one voice coil (single voice coil) or one subwoofer with dual voice coil are connected in parallel. Note: The parallel connection of two voice coils will result in halving the impedance! Maximum output power of this configuration: Two subwoofers with 1 x 4 Ohms correspond to a total Two subwoofers with a single voice coil...
Seite 18
Example configurations for Master / Slave Mode Amplifier connection in Master / Slave Mode Master Slave Signal from the radio Switch setting: Switch setting: (RCA/Cinch or highlevel) Master Slave RCA/Cinch cable Speaker connection in Master / Slave Mode Master Slave One subwoofer with one voice coil (single voice coil) Maximum output power of this configuration:...