Installation - simu T3.5 AUTO Bedienungsanleitung

T3.5 AUTO - T5 AUTO
230V ˜
S.A.S. au capital de 5 000 000 ! - Z.I. Les Giranaux - BP71 - F70103 Arc-Les-Gray CEDEX - RCS VESOUL B 425 650 090 - SIRET 425 650 090 00011 - n° T.V.A CEE FR 87 425 650 090
These instructions apply to all T3.5 AUTO / T5 AUTO drive, the different versions of which are available in the current catalogue.
field of application: The T3.5 AUTO / T5 AUTO drive is designed to drive all types of roller shutters equipped with stop blocks and rigid links. The installer,
who must be a motorisation and home automation professional, must ensure that the drive product is installed in accordance with the standards in force in the
country in which it is installed such as EN 13659 relating to roller shutters.
liability: Before installing and using the drive, please read operating and installation guide carefully. In addition to following the instructions given in this guide,
the instructions detailed in the attached Safety instructions document must also be observed. The drive must be installed by a drive and home automation
professional, according to instructions from SIMU and the regulations applicable in the country in which it is commissioned. It is prohibited to use the drive
outside the fields of application described above. Such use, and any failure to comply with the instructions given in this guide and in the attached Safety
instructions document, absolves SIMU of any liability and invalidates the warranty. The installer must inform its customers of the operating and maintenance
conditions for the drive and must provide them with the instructions for use and maintenance, and the attached Safety instructions document, after installing
the. Any After-Sales Service operation on the drive must be performed by a drive and home automation professional. If in doubt when installing the drive, or to
obtain additional information, contact a SIMU adviser or go to the website www.simu.com
1

installation

Instructions which must be followed by the drive and home automation professional installing the drive:
- Methods of wiring are given by national standards or IEC60364 standard.
- Cables which pass through a metal wall must be protected and isolated using a sheath or sleeve.
T3.5 AUTO: The cable for the T3.5 AUTO cannot be removed. If it is damaged, return the drive to the After-Sales
department.
T5 AUTO: The cable for the T5 AUTO can be removed. If it is damaged, replace by the same. The cable may only be
connected to the motor by qualified personnel. The connector is to be assembled without damaging the contacts. The
continuity of the earth connection must be ensured.
recommendations: The motor torque must be selected according to the shutter's characteristics. Do not oversize
the operator. The use of automatic locking devices (VAR, VAS or EASYLINK) and stops on the final slat is mandatory
in order to ensure proper working of the motor. To receive information regarding the compatibility of the motor and the roller shutter or/and
accessories, contact the roller shutter manufacturer or SIMU.
Drilling of the tube:
L1
29
Ø38,2
IP 44
L2
T3.5 AUTO 4.16
230V 50Hz 9.16 - 13.10
˜
Mounting T3.5 AUTO:
1/2
50Hz
A
4 x ØB / 90°
A ØB L1
(mm) (mm) (mm)
448 471
4.2
483 506
Ø4 x 10 / 120°
STEEL
55
22,8
37
min.
48*
L2
4
(mm)
* 35 Nm max.
6.17 - 10.17
485
T5 AUTO
15.17
520
230V 50Hz
˜
20.17 - 25.17 - 35.17
Mounting T5 AUTO:
1
9910013
9910014
25 N.m max.
eN- OrgiNAl iNSTrUcTiONS
5122380A
A
L1
IP 44
A ØB
L2
(mm) (mm)
485
5
505
659
5
4
3
2
2
1
2
3
1 2
i
-20°C / +60°C
V.A.R
V.A.S
EASYLINK
MANDATORY
4 x ØB / 90°
47
min.
L1 L2
(mm) (mm)
498 521
518 541
672 695
Ø4,8 x 10
STEEL
Ø5 x 10
1
35 N.m max.