Diagnostics On Digital Tv Channels; Options And Settings; Search For Tv Channels - IKEA UPPLEVA Handbuch

The 3D mode enables you to watch 3D
content on your TV. To use 3D follow these
steps.
1. Press MENU on the remote control and
select Picture > 3D navigation, then
press / to adjust 3D navigation to
Manual.
2. Press / to select 3D in the Picture
menu and press OK to enter the 3D
menu. (Refer to Figure 4.)
3. Put on your 3D glasses, then select
3D mode and press / to choose the
desired 3D input format.
4. Press / to select other menu options:
3D mode: Press / to select your
•
desired option between 3D-to-2D,
2D-to-3D and Off. 3D-to-2D will display
a 3D image in 2D (no 3D effect). The
2D-to-3D feature can be used to convert
2D images to 3D images. You need to
wear the UPPELVA 3D glasses to watch
the 3D images.
• Depth of field, Protrude, Distance
to TV: Press / to adjust to achieve a
good 3D effect with the image.
Image safety: Press / to select a
•
desired option among Low, Middle,
High and Off.
L-R switch: Select On or Off to adjust
•
the 3D video between the left and right
eyes for better 3D viewing.
5. Press EXIT to close the menu.
Notes:
— 3D glasses from other manufacturers
may not be supported.
— All photo functions are disabled in 3D
mode.
— If you change to a different signal
source or access Smart TV, the 3D mode
will be disabled automatically.
— Some 3D modes may not be available
depending on the input format of the 3D
video source.
— Supported 3D modes:
Analogue TV, SCART, Component:
2D-to-3D Digital TV, HDMI, USB, Videos
from internet: Top and Bottom, Side-
by-Side, 2D-to-3D, Line interleave,
Frame sequential.
— 3D function in USB mode: During the
playback of a selected video from USB,
press OPTION to display the video
menu in the browser mode, then select
3D Mode.

Diagnostics on digital TV channels

1. Press MENU on the remote control and
select Setup > Diagnostics.
2. Press OK to display some signal
information on the current digital
channel, such as signal strength,
frequency, etc.

7 Options and settings

Search for TV channels

This section describes how to search for and
store channels automatically. Instructions
are for both analogue and digital channels.
This may be done in any of the cases below:
you have selected Skip scan in the
─
Initial setup
─ you see "Please scan channels!" in TV
mode
─ you want to update your channels.
1. Press MENU on the remote control and
select Setup > Language. Press OK
to enter and press / to select your
desired menu language.
2. Press MENU to return to Setup, press
/ to select Country, then press /
to select your country. The TV installs
and arranges channels according to your
country. In this step, you will be asked
to enter your password.
3. Press / to select Tuner mode (the
way you get your TV signal), then press
/ to select Antenna or Cable or
Satellite. (Note: Satellite option may
not be available for certain models.)
Follow a) or b) or c) below depending on
how you get your TV signal.
a) If you have selected Antenna.
• Press / to select Channel
install, and press OK to enter.
• Select Automatic search (Refer to
Figure 2.), then press OK to enter
Automatic search.
Press OK to skip the country
•
selection and enter the next step.
Or use / to reselect your country,
then press OK to enter.
• Select Digital & Analogue or
Digital or Analogue, then press OK
to start the automatic search, which
relates to all digital (DVB-T) and/or
analogue channels.
b) If you have selected Cable.
35