Safety Instructions; Test Symbols; Appliance Description; Operation - STIEBEL ELTRON ESH 10 U-P Plus Bedienung Und Installation

OPErATION

Appliance description

2.2

Safety instructions

WARNING Burns
During operation, the tap can reach temperatures in ex-
cess of 60 °C.
There is a risk of scalding at outlet temperatures in ex-
cess of 43 °C.
WARNING Injury
!
The temperature selector should only be removed by a
qualified contractor.
WARNING Injury
!
The appliance may be used by children over 8 years of
age and persons with reduced physical, sensory or men-
tal capabilities or a lack of experience and expertise,
provided that they are supervised or they have been
instructed on how to use the appliance safely and have
understood the potential risks. Children must never play
with the appliance. Children must never clean the ap-
pliance or perform user maintenance unless they are
supervised.
Material losses
!
If the drain pipe of the safety valve is blocked, expanding
water can lead to water damage.
f Never close the drain pipe. f
Material losses
!
The user should protect the appliance and its tap against
frost.
2.3

Test symbols

See type plate on the appliance.
3. Appliance description
The appliance constantly keeps the water content available at the
preselected temperature. The appliance switches on automatically
as soon as its temperature falls below the set value.
Subject to season, varying cold water temperatures can result in
different maximum amounts of mixed outlet water.
Note
The appliance is under mains water pressure. The water
volume increases as the cylinder is being heated up. Dur-
ing this process, expansion water drips through the safety
valve. This is a necessary and normal process.
3.1 Operation
You can set any required DHW outlet temperature variably at the
temperature selector. The heat-up indicator illuminates during
the heat-up process.
14 | ESH 10 U-P Plus | ESH 10 O-P Plus
ESH 10 U-P Plus
1
2
1 Heat-up indicator
2 Temperature selector
Depending on the system, the actual temperatures may vary from
the set value.
• = Cold. On this setting, the appliance is protected from
frost. The tap and the water line are not protected.
E = Approx. 40 °C
e = Recommended energy saving setting (approx. 60 °C),
minor scaling
4.

Cleaning, care and maintenance

f Never use abrasive or corrosive cleaning agents. A damp f
cloth is sufficient for cleaning the appliance.
f Check the taps regularly. Limescale deposits at the tap out- f
lets can be removed using commercially available descaling
agents.
f Have the function of the safety valve checked regularly by a f
qualified contractor.
f Have the protective anode checked by a qualified contractor f
after the first 8 years of operation. The qualified contractor
will then determine the intervals at which repeat checks
should be performed.
Almost every type of water will deposit limescale at high temper-
atures. This settles inside the appliance and affects both perfor-
mance and service life. The heating elements should therefore be
descaled if necessary. A qualified contractor who is aware of the
local water quality will tell you when the next descaling is due.
5.

Troubleshooting

Fault Cause
The appliance does not The temperature
supply hot water. selector is set to
"•".
No power at the
appliance.
Water can only be The aerator in the
drawn at a reduced tap is scaled up.
rate.
Loud boiling noises in- The appliance is
side the appliance. scaled up.
Water drips from the The safety valve is
safety valve of the scaled up or dirty.
safety assembly after
heating has stopped.
If you cannot remedy the fault, contact your qualified contractor.
To facilitate and speed up your enquiry, please provide the serial
number from the type plate (000000-0000-000000).
ESH 10 O-P Plus
2
1
remedy
Switch the appliance ON by turn-
ing the temperature selector.
Check the plug / fuses in the dis-
tribution board.
Descale / replace the aerator.
Have the appliance descaled by a
qualified contractor.
Switch the appliance off. De-
pressurise the appliance by
disconnecting it from the power
and water supply. Have the safe-
ty valve checked by a qualified
contractor.
www.stiebel-eltron.com