OTD
x
TDIS
x*
PDIS
x*
CDIS
x*
SDIS
x*
DDIS
x*
ODB
x
x
x
INIT
x*
x*
x*
FLL
x*
x*
x*
STAB
x*
x*
x*
tDTO
x*
x*
x*
tFLL
x*
x*
x*
tSTB
x*
x*
x*
OBST
s*
RESE
x
x
x
UNIT
x
x
x
Legend
x
Appropriate channel is available.
x*
Appropriate channel is available subject to the associated option being enabled.
s*
System-specific channel is only available if the associated option has been enabled.
Appropriate channel is only available subject to the option "Heat metering" (OHQM) being enabled.
Appropriate channel is only available subject to the option "Heat metering" (OHQM) being disabled.
MEDT
The anti-freeze content channel (MED%) is only shown if the type of frost protection (MEDT) is not water or H-30 L/LS (MEDT 0 or 3).
Setting the anti-freeze content is only appropriate if anti-freeze is actually used in the solar circuit.
Note:
S3 and S4 are only displayed when the temperature sensors are connected (superimposed).
2.8.1 Display: Collector temperatures
COL, COL1, COL2:
Collector temperature
Display range:
-40 ... +260 °C
2.8.2 Display: Cylinder temperature
TST, TSTB,TSTT, TST1, TST2:
Cylinder temperatures
Display range:
-40... +260 °C
2.8.3 Display sensor 3 and sensor 4
S3, S4:
Sensor temperatures
Display range:
-40...+260 °C
2.8.4 Displaying other temperatures
TSFB, TRET, TR:
Other captured
temperatures
Display range:
-40 ... +260 °C
x
x*
x*
x*
x*
x*
x*
x*
x*
x*
x*
x*
x*
x
x
x
x
x
x
x
x
x
x
".+
323
32%!
Option, Pasteurisation
Pasteurisation temperature
Observation period
Countdown for observation period
Pasteurisation start time
Pasteurisation: Heat-up time
x
Option, Drainback
Display of the remaining time, Start con-
dition
Display of the remaining time, Filling
process
Display of the remaining stabilisation
time
Period, Start condition
Filling time of the Drainback function
Stabilisation time
Booster function (additional pump)
x
x
Reset to factory settings
x
x
Temperature unit
Shows the current collector temperature:
• COL
: Collector temperature (single collector system)
°C
• COL1 : Collector temperature 1
• COL2 : Collector temperature 2
Shows the current cylinder temperature:
• TST
: Cylinder temperature (single cylinder system)
°C
• TSTB : Lower cylinder temperature
• TSTT : Cylinder temperature, top
• TST1 : Temperature, cylinder 1
• TST2 : Temperature, cylinder 2
Shows the current temperature of the respective auxiliary sensor
(without control function).
°C
• S3
: Temperature sensor 3
• S4
: Temperature sensor 4
Note:
S3 and S4 are only displayed when the temperature sensors are
connected (superimposed).
Shows the current temperature of the respective sensor.
• TSFB : Temperature, solid fuel boiler
°C
• TRET : Heating return temperature
• TR
: Return temperature
OFF
OFF / ON
60 °C
0 ... 95 °C
01:00
0 ... 30:0 ... 24 (dd:hh)
00:00
00:00 ... 24:00
(hh:mm)
01:00
00:00 ... 24:00
(hh:mm)
OFF
OFF/ON
60 s
1 ... 100 s
5 min
1 ... 30 min
2 min
1 ... 15 min
OFF
OFF/ON
°C
°C / °F