Before Starting The Equipment - EINHELL TE-VC 2230 SAC Originalbetriebsanleitung

5. Before starting the equipment

Warning!
Before you connect the equipment to the power
supply make sure that the data on the rating plate
are identical to the supply voltage.
The equipment may be connected only to a
shock-proof socket-outlet.
5.1 Assembling the equipment
Fitting the wheels (Fig. 4-11)
Place a split pin for fi tting the wheels (31) through
the appropriate hole in the axle (33) and fi t a
washer (30), a wheel (13) and a washer to the
axle (33) (Fig. 5-6). Now slide the axle (33)
through the guides provided for it on the undersi-
de of the tank (10) (Fig. 7). Fit a washer and the
second wheel (13) to the empty end of the axle
(33) and secure it with the other washer (30) and
the split pin (31) (Fig. 8-10). Push the covers (32)
on to the outside of the wheels (13) so that the
detents engage on the covers (32) for the wheel
(13). (Fig. 11).
Fitting the castors (Fig. 12)
Fit the castors (12) into the appropriate moun-
tings on the underside of the tank (10). Push the
castors (12) fi rmly into the mounting until they
engage with a clicking noise (Fig. 12).
Fitting the push bar (Fig. 13)
Fit the push bar handle (35) onto the push bar
mounts (a) of the tank and secure the push bar
with the supplied screws (34) and fastening nuts
(38) as shown in Figure 13.
Fitting the head (Fig. 14-15)
The equipment head (5) is fastened to the tank
(10) by the locking hook (18). To remove the
equipment head (5), open the locking hook (18)
and take off the equipment head (5). When fi tting
the appliance head (5), make sure that the lo-
cking hook (18) locks into place correctly.
5.2 Fitting the fi lters
Important!
Never use the wet and dry vacuum cleaner wit-
hout a fi lter.
Always ensure that the fi lters are securely seated.
Fitting the foam fi lter (Fig. 16)
For wet-vacuuming, slip the supplied foamed
plastic fi lter (25) over the fi lter basket (Figs. 2/20).
Anl_TE_VC_2230_SAC_SPK9.indb 20 Anl_TE_VC_2230_SAC_SPK9.indb 20
GB
The pleated fi lter (Fig. 3/24) already fi tted upon
delivery is not suitable for wet-vacuuming!
Fitting the pleated fi lter (Fig. 17)
For dry-vacuuming, slip the pleated fi lter (Fig.
3/24) over the fi lter basket (Fig. 2/20). The pleated
fi lter (Fig. 3/24) is suitable for dry-vacuuming only.
Fitting the coarse fi lter (Fig. 18a)
The coarse fi lter (16) can be used for suctioning
large amounts of fi ne dust (with or without a dirt
collector bag).
Important! The coarse fi lter is not suitable for
wet vacuuming!
Place the coarse fi lter (16) on the rim of the con-
tainer (10) as shown in Fig. 18a. Ensure that the
coarse fi lter is fi tted completely on the rim of the
container.
Fitting the sealing ring (Fig. 18b)
The sealing ring (37) must fi tted for wet suctioning
and whenever the coarse fi lter is not used.
Place the sealing ring (37) on the rim of the con-
tainer (10) as shown in Fig. 18b. Ensure that the
sealing ring is fi tted completely on the rim of the
container.
5.3 Fitting the tank bag (Fig. 19)
Fit the dirt bag (Fig. 3/27) as shown in Figure 19.
5.4 Fitting the suction hose (Fig. 1-3; 19)
Connect the suction hose (9) to the correspon-
ding connector on the wet and dry vacuum clea-
ner, depending on the application required.
Vacuuming
Connect the suction hose (9) to the suction hose
connector (8).
Blowing
Connect the suction hose (9) to the blow connec-
tor (19).
Air regulator (Fig. 3)
The air regulator (29) can be fi tted between the
suction hose (9) and the suction tube (17). The
suction power of the nozzle can be infi nitely ad-
justed using the air regulator (29).
When wet vacuuming, make selective use of the
air regulator to suck in air as well as liquids. This
will help to take some strain off the equipment
when vacuuming liquids.
- 20 -
14.11.2018 13:54:23 14.11.2018 13:54:23