Makita 4101RH Betriebsanleitung Seite 6

16. Remove adjusting keys and wrenches
Form the habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
17. Avoid unintentional starting
Don't carry plugged-in tool with finger on switch.
Be sure switch is off when plugging in.
18. Outdoor use extension cords
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
19. Stay alert
Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
20. Check damaged parts
Before further use of the tool, a guard or other
part that is damaged should be carefully checked
to determine that it will operate properly and per-
form its intended function. Check for alignment of
moving parts, binding of moving parts, breakage
of parts, mounting, and any other conditions that
may affect its operation. A guard or other part
that is damaged should be properly repaired or
replaced by an authorized service center unless
otherwise indicated elsewhere in this instruction
manual. Have defective switches replaced by
and authorized service center. Do not use tool if
switch does not turn it on and off.
21. Warning
The use of any other accessory or attachment
other than recommended in this operating
instruction or the catalog may present a risk of
personal injury.
22. Have your tool repaired by an expert
This electric appliance is in accordance with the
relevant safety rules. Repairing of electric appli-
ances may be carried out only by experts other-
wise it may cause considerable danger for the
user.
ADDITIONAL SAFETY RULES
1. This tool is equipped with a portable residual
current device. Do not connect the tool to a
power supply without using the PRCD (Porta-
ble Residual Current Device). In case of dam-
age of the cord, it has to be replaced by the
manufacturer's service organization.
2. For additional protection against electric
shock, be sure to WEAR RUBBER GLOVES
AND RUBBER BOOTS during operation.
3. Check the wheel carefully for cracks or dam-
age before operation. Replace cracked or
damaged wheel immediately.
4. Use only flanges specified for this tool.
5. Be careful not to damage the spindle, flanges
(especially the installing surface) or bolt.
Damage to these parts could result in wheel
breakage.
6. When using the water feed, be careful not to
let water get into the motor. If water runs into
the motor, an electric shock hazard may
result.
7. Hold the tool firmly.
6
8. Keep hands away from rotating parts.
9. Make sure the wheel is not contacting the
workpiece before the switch is turned on.
10. Wait until the wheel attains full speed before
cutting.
11. Stop operation immediately if you notice any-
thing abnormal.
12. Do not attempt to lock the trigger in the "ON"
position.
13. Never attempt to cut with the tool held upside
down in a vise. This can lead to serious acci-
dents, because it is extremely dangerous.
(Fig. 1)
14. Before setting the tool down after completing
a cut, be sure that the wheel has come to a
complete stop.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing water pipe (Fig. 2)
First, unplug the tool. Loosen the wing bolt on the
depth guide and move the base down. Install the
water pipe on the blade case using the screw as
shown in Fig. 2. Attach the vinyl tube onto the water
pipe and attach the adapter on the vinyl tube to a fau-
cet of water mains pressure. Adjust the amount of
water flow by simply adjusting the water cock.
Installing or removing diamond wheel
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the wheel.
Hold the outer flange with the wrench and loosen the
hex socket head bolt in clockwise direction with the
hex wrench. Then remove the hex socket head bolt
and outer flange. (Fig. 3)
Install the diamond wheel, outer flange and hex
socket head bolt onto the spindle. Hold the outer
flange with the wrench and tighten the hex socket
head bolt in counterclockwise direction with the hex
wrench. BE SURE TO TIGHTEN THE HEX SOCKET
HEAD BOLT SECURELY. (Fig. 4)
CAUTION:
Use only the Makita wrench and hex wrench to install
or remove the wheel.
Adjusting depth of cut (Fig. 5)
Loosen the wing bolt on the depth guide and move
the base up or down. At the desired depth of cut,
secure the base by tightening the wing bolt.