Slave Mode - Cameo HYDRABEAM 1000 RGBW Bedienungsanleitung

DMX MODE SETTING
Press MENU to access the selection menu for system settings. Using the UP and DOWN controls, select the menu item "DMX Mode"
(coloured background) and confirm with ENTER. A selection box is displayed and you can select the desired DMX mode with the help of the
UP and DOWN controls. Confirm the entry with ENTER and press MENU to return to the main display. The main display is activated automat-
ically after approximately 1 minute of inactivity. The DMX start address is clearly visible in the middle of the display and the DMX mode is
displayed on the bottom line (03Ch, 06Ch, 09Ch, 12Ch 14Ch). If the DMX signal is interrupted, the DMX address symbol will begin to flash. It
will stop flashing once the DMX signal is restored.
System Settings
CH-03
DMX Address 001
CH-06
DMX Mode CH-14
Auto Mode Auto06 CH-09

Slave Mode

Off
CH-12
Advanced Settings
CH-14
CONFIGURING AUTO MODE
Each of the 7 available auto programmes consist of a sequence of pre-configured colour change and motion sequences.
Press MENU to access the selection menu for system settings. Using the UP and DOWN controls, select the menu item "Auto Mode"
(coloured background) and confirm with ENTER. Use the UP and DOWN controls to select "Show Mode" and confirm with ENTER. Use UP
and DOWN to select the desired programme (Auto00 to Auto06) and confirm with ENTER. To configure programme run speed, use the UP
and DOWN keys to select the menu item "Show Speed" and confirm with ENTER. Use the UP and DOWN controls to select a value between
01 and 99 (press and hold for quick change of value. 01 = minimum and 99 = maximum speed). Confirm the entry with ENTER and press
MENU to return to the main display. After about 1 minute of inactivity, the main display is automatically activated and the mode is clearly
shown in the centre of the display.
System Settings Auto Mode
DMX Address 001 Show Mode
DMX Mode CH-14 Show Speed
Auto Mode Auto06 Sound Mode
Slave Mode Off Sound Sens
Advanced Settings
ACTIVATING SOUND CONTROL
Select one of the Auto-programmes as previously described under "CONFIGURING AUTO MODE". Using the UP and DOWN buttons, select the
menu item "SOUND Mode" (coloured background) and confirm with ENTER, then use UP and DOWN once again to select "On" and confirm
with ENTER. To configure microphone sensitivity, use the UP and DOWN keys to select the menu item "Sound Sens" and confirm with
ENTER. Use the UP and DOWN controls to select a value between 00 and 99 (press and hold for quick change of value. 00 = minimum and
99 = maximum sensitivity). Confirm the entry with ENTER and press MENU to return to the main display. After about 1 minute of inactivity,
the main display is automatically activated and the mode is clearly shown in the centre of the display. The spotlight will now be controlled
via the built-in microphone and will follow the rhythm of the music (bass signals).
Auto Mode Operating Mode
Show Mode Auto00-06
Show Speed 01-99
Sound Mode Off/On
Sound Sens 00-99
Sens: 099
SLAVE MODE
Press MENU to access the selection menu for system settings. Using the UP and DOWN controls, select the menu item "Slave Mode" (coloured
background) and confirm with ENTER. Press MENU to return to the main display. After about 1 minute of inactivity, the main display is
automatically activated and "SLAVE" is clearly shown in the centre of the display. Connect the slave and the master units (same model) with a
DMX cable and enable one of the standalone modes on the master unit (Auto, Sound). Now the slave unit will follow the master unit.
System Settings Operating Mode
DMX Address 001
DMX Mode CH-14
Auto Mode Auto06
Slave Mode On
Advanced Settings
6
Operating Mode
001
Channel mode: 14Ch
Operating Mode
Auto00-06
01-99
AUTO
Off/On
00-99
Speed: 099
SOUND
SLAVE