Makita DTR180 Betriebsanleitung Seite 14

NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem. This system automatically cuts off power to the
motor to extend tool and battery life. The tool will auto-
matically stop during operation if the tool or battery is
placed under one of the following conditions:
Overload protection
When the battery is operated in a manner that causes
it to draw an abnormally high current, the tool auto-
matically stops and the corresponding error number is
displayed on the display panel. In this situation, turn the
tool off and stop the application that caused the tool to
become overloaded. Then turn the tool on to restart.
Overheat protection
When the tool or battery is overheated, the tool stops
automatically and the corresponding error number is
displayed on the display panel. In this case, let the tool
and battery cool before turning the tool on again.
Overdischarge protection
When the battery capacity is not enough, the tool stops
automatically and the corresponding error number is
displayed on the display panel. In this case, remove the
battery from the tool and charge the battery.
Main power switch
CAUTION:
When you turn the power on, never
bring your limbs or face close to the binding or
rotating parts of the tool tip. Otherwise, you may
be injured.
CAUTION:
When the power is turned on,
never touch the binding or rotating parts of the
tool tip. Otherwise, you may be injured.
CAUTION:
Before inserting the battery car-
tridge, be sure to release your fingers from the
switch trigger and lock the trigger. If you insert
the battery cartridge while the switch trigger is being
pulled, it may cause an accident if the wire tying
process is accidentally carried out.
► Fig.3
When you press the power button, the power turns
on and the tying mode lamp lights up. In order for the
tool to adjust its initial position, it operates temporarily.
When adjustment has completed, the tool stops auto-
matically. When you press the power button again, the
power turns off and the tying mode lamp goes out.
► Fig.4: 1. Tying mode lamp 2. Power button
NOTE: The tool has an auto power-off function. If the
switch trigger is not pulled for 10 minutes, the tool
is automatically turned off to reduce battery power
consumption.
NOTE: To restart the tool, turn the power on again.
Mode switching button
When the power is turned on and the tying mode lamp
is lit, you can select the single actuation mode or the
continuous actuation mode via the mode switching but-
ton. When you turn the power on again, the tool starts in
the mode that was most recently selected.
► Fig.5: 1. Mode switching button 2. Single actuation
mode 3. Continuous actuation mode
Switch action
WARNING:
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
CAUTION:
When not operating the tool,
depress the trigger-lock button from
lock the switch trigger in the OFF position.
► Fig.6: 1. Switch trigger 2. Trigger-lock button
To prevent the switch trigger from accidentally pulled,
the trigger-lock button is provided. To start the tool,
depress the trigger-lock button from A side and pull the
switch trigger. Release the switch trigger to stop. After
use, press in the trigger-lock button from B side.
When you pull the switch trigger, the tool performs the
next sequential operations as follows, and the tool stops
automatically.
1. Feed the wire.
2. Cut the wire.
3. The hook holds and twists the wire.
4. The hook returns to the original position.
Tying strength setting
CAUTION:
Be sure to lock the trigger before
starting the adjustment. When you turn the power
on, never bring your limbs or face close to the
binding or rotating parts of the tool tip. Otherwise,
you may be injured.
► Fig.7
You can set the tying strength by adjusting the tying
strength adjusting button. Tying strength is shown on
the display panel.
► Fig.8: 1. Tying strength adjusting button 2. Display
panel
If the wire is broken off, tying strength will be lost. After
tying, check the twisted portion for breakage.
If the wire is broken off, adjust the tying strength using the
tying strength adjusting button, and tie the rebars again.
Remaining battery notification
When the battery voltage drops below the required level,
the tool will stop operating, an error tone will sound, and
the number "4" will appear on the display panel. The error
tone will continue to sound until the power is turned off.
NOTE: If the ambient temperature is extremely low,
the error tone may sound even when the battery
contains sufficient power.
14 ENGLISH
Before installing the battery car-
side to