Specifications; Safety Instructions - Makita BO4900V Betriebsanleitung

ENGLISH
1 Clamp lever
2 Conventional type of abrasive
paper with pre-punched holes
3 Pad
4 Punch plate
5 Conventional type of abrasive
paper without pre-punched
holes

SPECIFICATIONS

Model
Pad size ..........................................................115 mm x 229 mm
Abrasive paper size ........................................115 mm x 280 mm
–1
Orbits per minute (min
Sanding stroke rate (min
Overall length .................................................289 mm
Net weight ......................................................2.8kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for the sanding of large surface of
wood, plastics and metal materials as well as painted
surfaces.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.

SAFETY INSTRUCTIONS

Warning! When using electric tools, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury,
including the following. Read all these instruc-
tions before attempting to operate this product
and save these instructions.
For safe operation:
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Don't expose power tools to rain. Don't use
power tools in damp or wet locations. Keep work
area well lit. Don't use power tools in presence of
flammable liquids or gases.
3. Guard against electric shock
Prevent body contact with grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
4. Keep children away
Do not let visitors contact tool or extension cord.
All visitors should be kept away from work area.
4
Explanation of general view
6 Hook-and-loop type of
abrasive paper with
pre-punched holes
7 Pad for hook-and-loop type of
abrasive paper
8 Screws
9 Screwdriver
10 Groove
11 Front fixing cardboard
BO4900V
) ................................4,000 – 10,000
–1
).............................8,000 – 20,000
12 Paper dust bag
13 Claws
14 Upper part
15 Notch
16 Guide
17 Speed adjusting dial
18 Lock button
19 Switch trigger
BO4900
115 mm x 229 mm
115 mm x 280 mm
10,000
20,000
289 mm
2.8kg
5. Store idle tools
When not in use, tools should be stored in dry,
high, or locked-up place, out of the reach of chil-
dren.
6. Don't force tool
It will do the job better and safer at the rate for
which it was intended.
7. Use right tool
Don't force small tools or attachments to do the
job of a heavy duty tool. Don't use tools for pur-
poses not intended; for example, don't use circu-
lar saw for cutting tree limbs or logs.
8. Dress properly
Do not wear loose clothing or jewelry. They can
be caught in moving parts. Rubber gloves and
non-skid footwear are recommended when work-
ing outdoors. Wear protective hair covering to
contain long hair.
9. Use safety glasses and hearing protection
Also use face or dust mask if cutting operation is
dusty.
10. Connect dust extraction equipment
If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used.
11. Don't abuse cord
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and
sharp edges.
12. Secure work
Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to oper-
ate tool.
13. Don't overreach
Keep proper footing and balance at all times.
BO4901
115 mm x 229 mm
115 mm x 280 mm
10,000
20,000
289 mm
2.8kg