Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
DESCRIPTION
Electrical slicer machine for
within the dimensional limits
indicated in this manual. The
main parts that make up this
ure 1. Electrical diagrams are
DECLARATION OF
CONFORMITY
The machines described in this
an Regulation (EC) 1935/2004
and with relative standards
EN60335-2-14.
SAFETY
Please observe the following
- carefully read all instructions
before using the machine;
- the product is not intended to
- use the machine only if you
- do not use the machine in any
this manual;
- install the machine in con-
indicated in the "Installation"
section;
- install the machine in a loca-
tion out of the reach of person-
nel unauthorised to operate it;
- stay highly concentrated when
distraction during use;
home use with circular blade,
designed solely to slice food
products of the types and
machine are illustrated in fig-
reported in Fig. 2.
manual comply with 2006/95/
CE, 2004/108/CE, 2012/19/
UE, 2011/65/CE, with Europe-
such EN60204-1, EN60335-1,
instructions for your safety:
be used by children;
have been properly trained
and are in perfect psychologi-
cal and physical condition;
way other than as described in
formity to the instructions
using the machine and avoid any
- do not allow the machine
prehended the content of this
manual;
- do not wear baggy clothing or
clothing with open sleeves;
- do not allow anyone besides
the operator to approach dur-
ing product cutting operations;
- do not remove, cover or
- do not remove the transpar-
ent protections and do not
ical and electrical protective
devices;
- slice only the permitted prod-
ucts. Do not attempt cuts on
- always keep the sliced prod-
area all around the machine
- do not use the machine as
a resting surface and do not
are foreign to normal cutting
operations;
- do not use the slicer when,
tance between the edge of the
blade and the blade protection
exceeds 5 mm;
- in this case, contact the man-
ufacturer or an Authorised
Service Centre to change the
blade;
- do not use the machine with
non insulated cables;
- periodically check the con-
dition of the power cable and
the cable gland on the machine
12
to be used by personnel who
have not read and fully com-
modify the tags located on the
machine body and, in case of
damage of these, replace them
promptly;
modify or bypass the mechan-
prohibited type products;
uct resting surface, the work
and the operator floor area
clean and dry;
place any objects on it which
due to normal wear, the dis-
"movable" type electrical con-
nections, with temporary or
body. Replace it promptly
when necessary, requesting
operation by qualified person-
nel;
- immediately stop the ma-
- before cleaning or carrying
the machine from the electri-
cal mains;
- use protective gloves for the
cleaning and maintenance op-
erations;
- place and remove the goods
to be sliced on the sliding meat
with the thickness adjustment
- for movement of the meat
table during cutting operations
dle located on the arm or the
product holder grip;
- use of cutting accessories
the manufacturer with the ma-
chine is prohibited;
- the device cannot be used
without the meat table or
product holder.
direct and indirect responsibil-
cations and/or repair carried
non original accessories and
replacement parts.
in open areas and/or areas
which are exposed to atmos-
pheric agents and in environ-
or corrosive and/or abrasive
the use of anti-explosive com-
ponents is required.
chine in the event of a defect,
abnormal operation, suspicion
of breakdown, incorrect move-
ment, unusual noises;
out maintenance, disconnect
table only with the carriage
completely pulled back and
lever placed in the safety posi-
tion (Fig. A);
use only the manoeuvring han-
which were not provided by
The manufacturer declines any
ity stemming from inappropri-
ate use, unauthorised modifi-
out on the machine, or use of
The machine may not be used
ments with vapours, fumes
powders, with risk of fire or ex-
plosion and in any case where
Werbung
Inhaltsverzeichnis
