Maintenance; Maintenance Schedule - Husqvarna 129 RJ Bedienungsanweisung

2. Pull the choke control up (Picture 30).
3. Hold the body of the product on the ground with your
left hand (Picture 31). Do not step on the product.
Pull the starter rope handle slowly until you feel
some resistance. Then pull the starter rope handle
with force.
N N ote: Do not pull the throttle trigger while you start
the engine.
4. Continue to pull the starter rope handle until the
engine starts or tries to start (max. 3 pulls). If the
engine starts or tries to start, push the choke control
down. Continue to pull until the engine starts. Wait
60 seconds after a start before you pull the throttle
trigger.
CAUTION: Do not pull the starter rope
until it stops. Do not let go of the starter
rope when it is fully extended. Release
the starter rope slowly. Failure to obey
these instructions can cause damage to
the engine.
To start a warm engine
1. Push the primer bulb 10 times.
2. Pull the starter rope until the engine starts.
To stop
• Push the stop switch to stop the engine. (Picture 21)
Note: The stop switch automatically goes back to its
initial position.
To operate the grass trimmer
CAUTION: Make sure that you slow the
engine to idle speed after each operation. A
long period at full throttle without a load on
the engine can cause damage to the engine.
Note: Clean the cover of the trimmer head when you
attach a new trimmer line to prevent vibrations. Examine
other parts of the trimmer head and clean if it is
necessary.
To trim the grass
1. Hold the trimmer head immediately above the
ground at an angle (Picture 34) . Do not push the
grass trimmer line into the grass.
WARNING: Read and understand the safety
chapter before you clean, repair or do
maintenance on the product.
12
2. Decrease the length of the grass trimmer line by
10-12 cm (4-4.75 in) and decrease engine speed to
decrease the risk of damage to plants.
3. Use 80 % throttle when you cut grass near objects
(Picture 35).
To cut the grass
1. Make sure that the grass trimmer line is parallel to
the ground when you cut (Picture 36).
2. Do not push the trimmer head to the ground. The
ground and the product can be damaged.
3. Do not let the trimmer head touch the ground
continuously, it can cause damage to the trimmer
head.
4. Use full throttle when you move the product from
side to side (Picture 37) to cut grass. Make sure that
the grass trimmer line is parallel to the ground.
To clear grass with a grass blade
1. Grass blades and grass cutters must not be used on
woody stems.
2. A grass blade is used for all types of tall or coarse
grass.
3. The grass is cut down with a sideways, swinging
movement, where the movement from right-to-left is
the clearing stoke and the movement from left-to-
right is the return stoke. Let the left-hand side of the
blade (between 8 and 12 o'clock) do the cutting.
4. if the blade is angled to the left when clearing grass,
the grass will collect in a line, which makes it easier
to collect, e.g. by raking.
5. Try to work rhythmically. Stand firmly with your feet
apart. Move forward after the return stoke and stand
firmly again.
6. Let the support cup rest lightly against the ground. It
is used to protect the blade from hitting the ground.
7. Reduce the risk of material wrapping around the
blade by always work at full throttle and avoid the
previously cut material during the return stoke.
8. Stop the engine, unclip the harness and place the
machine on the ground before you start to collect the
cut material.
To replace the trimmer line
See picture 47 to picture 54.

MAINTENANCE

Maintenance schedule

Make sure that you obey the maintenance schedule.
The intervals are calculated from daily use of the
product. The intervals are different if you do not use the
194 - 002 -