TermaTech TT22 Montage- Und Bedienungsanleitung Seite 23

On your new TT22 the work with controlling the air input has been simplified so there is only one
knob/damper (below the door).
Between the left position and the middle position you have the normal area where you control the
air input.
No air input = left position and
Maximum air input = middle position.
As help for lighting the control knob/damper can be pushed down a little and pushed completely
to the right. This start help adds some air from below and ensures faster lighting. After a few
minutes the control knob/damper is returned to the normal position (between the left and middle
position).
Lighting and continuous firing at EN-testing
1. The damper/start-up device can be opened (the knob is pushed down and to the right) for a
few minutes at lighting. Put about 12-15 kindling sticks (dia. 2-5 cm) in the bottom of the stove,
laid in a criss-cross pattern as a log house. Put 2 firelighters in the middle and light them.
2. Leave the door ajar so there is an opening of about 1 cm. Leave the stove like that for about
8-10 minutes before you close the door completely. Stay by the stove as long as the door is ajar.
3. When the fire has burned to embers (there are no more flames) open the door gently so the
ash is not whirled out through the door. Gently spread out the embers with a poker so they are
even.
4. Put 2-4 pieces of firewood in the stove, about 2,0 to 2,5 kg total. The pieces are put in the bot-
tom of the stove and parallel to the front of the stove with equal distance to the stove's sides and
with mutual distance of about 1 cm. The front piece is best lit if it has a split side that is turned
to the door and one in the embers. Close the door completely immediately. Make sure you don't
overfill the chamber, max.15 cm from the bottom plate of the combustion chamber.
5. The knob/damper is opened so it is about 2/3 open (between the left and middle position)
and after about 2 minutes the damper is set to about 1/3 open. How much the damper should be
open depends on the individual chimney's draught, but the flames should now stabilise to a calm
fire.
6. When the wood has burned to embers (after about 45-60) you start again from point 3.
MAINTENANCE – always use original parts
Maintenance and cleaning of the stove should only be performed when the stove is cold.
The daily maintenance is limited, but once a year the stove should get thorough maintenance.
The combustion chamber should be cleaned for ashes and soot and the door hinges and the clo-
sing mechanism should be lubricated with copper grease.
The surface is maintained by brushing it with a soft, long-haired brush or by using the vacuum
cleaner with a brush. The stove can also be dusted with a duster. Always remember: only when
the stove is cold.
Jointings can look okay, but they collapse under the heat and thereby lose the ability to keep the
stove sealed. Jointings should be changed as needed as it is important to good combustion and a
clean window that the stove is sealed.
The insulation plates in the combustion chamber that are broken or worn can easily be changed
as they are loosely fixed. The material used is called Vermiculite and is a porous, but very suitable
insulation material. It has no effect on the stove's efficiency that the insulation cracks. However, it
should be changed when the wear surpasses half of the original thickness.
Painting the stove with Senotherm-spray can cover spots or small scratches from kettles and
such. Larger damages needs to be ground with fine steel wool, vacuumed and then sprayed.
The can has to be shaken vigorously and then sprayed on at a distance of 15-20 cm. It is very
important that the stove is not in use and completely cold before you use the spray due to the fire
hazard. In order to keep the stove's varnished surfaces looking nice for years to come you should
try to avoid touching the varnished surfaces when the stove is hot. Make sure to have sufficient
ventilation when using spray paint.
Glass normally does not need any maintenance apart from cleaning. This is most easily done
by using TermaTech's glass cleaner. Remember only to use glass cleaner when the stove is cold.
Glass is made of ceramic glass, be sure of environmentally disposal.
Original parts which need to be changed due to wear can be found at your dealer. Because of fit
etc. only original parts from TermaTech should be used.
23