Einrichtungsassistent Für Anwendungen Mit Regelung Mit Rückführung - Danfoss VLT HVAC Basic Drive FC 101 Kurzanleitung

Programmieren
Einrichtungsassistent für Anwendungen mit Regelung mit Rückführung
PM motor
1-24 Motor Current
3.8 A
1-25 Motor Nominal Speed
3000 RPM
1-26 Motor Cont. Rated Torque
5.4 Nm
1-30 Stator Resistance
0.65 Ohms
1-39 Motor Poles
8
1-40 Back EMF at 1000 RPM
57 V
6-22 T54 Low Current
04.66 A
6-24 T54 low Feedback
0016 Hz
6-23 T54 high Current
13.30
A
6-25 T54 high Feedback
0050
Hz
Abbildung 4.5 Einrichtungsassistent für Anwendungen mit Regelung mit Rückführung
Parameter 1-46 Verstärkung Positionserkennung und Parameter 1-70 PM-Startfunktion sind ab Softwareversion 2.80 verfügbar.
MG18A803
Kurzanleitung
0-03 Regional Settings
[0] Power kW/50 Hz
0-06 Grid Type
[0] 200-240V/50Hz/Delta
1-00 Con guration Mode
[3] Closed Loop
1-10 Motor Type
[0] Asynchronous
Motor type = IPM
1-38 q-axis inductance(Lq)
5 mH
Motor type = SPM
IPM type = non-Sat.
(1-70) PM Start Mode
[0] Rotor Detection
1-46 Position Detection Gain
100 %
30-22 Locked Rotor Detection
[0] O
30-23 Locked Rotor Detection Time[s]
0.10 s
4-19 Max Ouput Frequency
0065 Hz
1-42 Motor Cable Length
50
m
4-12 Motor speed low limit
0016 Hz
4-13 Motor speed high limit
0050 Hz
3-41 Ramp 1 ramp-up time
0010 s
3-42 Ramp1 ramp-down time
0010 s
Motor type = PM motor
20-00 Feedback 1 source
[1] Analog input 54
3-16 Reference Source 2
[0] No Operation
3-02 Min Reference
0.00
3-03 Max Reference
50.00
3-10 Preset reference [0]
0.00 %
6-29 Terminal 54 Mode
Current
[1] Voltage
6-26 T54 Filter time const.
s
0.01
20-81 PI Normal/Inverse Control
[0] Normal
20-83 PI Normal/Inverse Control
0050 Hz
20-93 PI Proportional Gain
00.50
20-94 PI integral time
0020.00 s
1-29 Automatic Motor Adaption
[0] O
Danfoss A/S © 05/2016 Alle Rechte vorbehalten.
Asynchronous motor
1-20 Motor Power
1.10 kW
1-22 Motor Voltage
400 V
1-23 Motor Frequency
50 Hz
1-24 Motor Current
04.66 A
1-25 Motor nominal speed
1420 RPM
1-44 d-axis Inductance Sat. (LdSat)
IPM type = Sat.
5
mH
(1-45) q-axis Inductance Sat. (LqSat)
5
mH
(1-48) Current at Min Inductance for d-axis
100
%
1-49 Current at Min Inductance for q-axis
100 %
Motor type = Asynchronous
1-73 Flying Start
[0] No
This dialog is forced to be set to
[1] Analog input 54
Voltage
6-20 T54 low Voltage
0050 V
6-24 T54 low Feedback
0016 Hz
6-21 T54 high Voltage
0220 V
6-25 T54 high Feedback
0050 Hz
4 4
33