Initial Lubrication; Starting Operation - Jet JMD-2 Gebrauchsanleitung

The mains connection must have a
16 A surge-proof fuse.
Only use power cords marked
H07RN-F.
Connections and repairs to the
electrical equipment may only be
carried out by qualified electricians.

5.4 Initial lubrication

The machine must be serviced at all
lubrication points before it is placed
into service!
Failure to comply may cause serious
damage.
(see chapter 8 for lubrication)

5.5 Starting operation

Before starting the machine check
the proper chucking (see chapter 7.2)
Connect the machine to electric
power, the power indication lamp
(N, Fig 3) is illuminated when
connected.
You can start the machine with the
green ON-button (R, Fig 4)
The red OFF-button (Q) stops the
machine.
The speed can be adjusted with the
+/- buttons (T).
Use the arrow buttons (S) to reverse
the spindle direction.
Only half maximum speed in reverse
direction.
Fig 4
The RPM will be shown on the display
(V).
The emergency stop button (P) stops
all machine functions.
Attention:
The machine still has electric power!
Turn emergency stop button clockwise
to reset.
Disconnect the machine from the
power source if not in use (pull mains
plug).
Tapping function:
Push the tapping button (U), the
tapping mode control light will be on
Choose a low speed for tapping.
Tapping speed is limited to 500rpm.
To reverse direction push the tapping
control buttons on the down feed
handles (B, Fig 1).
Fuse protection:
The fuse (O) protects the motor and
electronic parts.
The fuse may only be changed when
the machine is disconnected from
power source (pull mains plug).
6. Machine operation
Warning:
Setup work may only be carried out
after the machine is protected
against accidental starting.
With pressed emergency stop
button.
Never place your fingers in a position
where they could contact any rotating
tool, chuck or cutting chips.
Remove cutting chips with the aid of
an appropriate chip hook when the
machine is at a standstill only.
Never stop the rotating chuck or tool
with your hands.
Always close the chuck guard before
you start the machine.
Secure work piece to the table with
clamps or a vice to prevent rotating
with the drill bit.
When using a vice, always fasten it to
the table.
Check the save clamping of the work
piece, chuck and tools before starting
the machine.
Never do any works "freehand" (hand-
holding the work piece rather than
supporting it on the table).
Support long work pieces with helping
roller stands.
Always adjust the depth stop to
prevent drilling into the table or into
the workholding device.
6
Feed a drill bit into the material with
only enough force to allow the drill bit
to work.
Feeding too slowly may cause burning
of the work piece or tool. Feeding too
quickly may cause the motor to stop
and/or the drill bit to break.
Do not use wire wheels or grinding
wheels on this machine.
Never cut magnesium-
high danger to fire!
Measurements and adjustments may
be carried out when the machine is at
a standstill only.
In case of danger push the
emergency stop button.
6.1 Spindle speeds selection
The correct spindle speed depends on
the type of machining, the cutting
diameter, the material to be machined
and the cutting tool.
These are recommended max. speeds
for a 10mm high speed steel (HSS)
tool (e.g. drill bit).
Aluminium, brass
Cast iron
Mild steel
High carbon steel
Stainless steel
If a carbide (HM) tool is used about 5
times higher speeds can be chosen.
Generally speaking:
the larger in relation the cutting
diameter, the smaller the possible
RPM.
For example:
Milling mild steel with an end mill of
20mm allows a speed of:
400 RPM max.
2000 RPM max. with carbide tool
Note:
Choose a low speed for tapping.
Tapping speed is limited to 500rpm.
7. Setup and adjustments
Warning:
Setup and adjustment work may
only be carried out after the
machine is protected against
accidental starting.
Push the emergency stop button
and disconnect from the power
source!
1500 RPM
1000 RPM
800 RPM
600 RPM
300 RPM
with HSS tool