Sanitizzazione Del Distributore Montato; Manutenzione; Manutenzione (Solo A Cura Del Servizio Di Assistenza); Technical Characteristics - Ugolini HT 10 Gebrauchsanweisung

HT10 - HT11 - HT20

1 TECHNICAL CHARACTERISTICS

Transparent removable bowls
Capacity of each bowl, approx.
Dimensions:
width
depth
height
Net weight, approx.
Gross weight, approx.
Adjustable thermostats
Hermetic compressor
Air-cooled condenser
Overload protector
Noise level lower than 70 dB (A)
IMPORTANT
Read electrical ratings written on the data plate of the
individual units; the data plate is adhered on the
dispensing side panel of the unit, just behind the drip
tray (the right side drip tray in multiple bowl models).
The serial number of the unit (preceded by the symbol #)
is adhered just below the right bowl. Data plate
specifications will always supersede the information in
this manual.
Specifications are subject to change without notice.

2 INTRODUCTION

Please read all sections of this manual thoroughly to familiarize
yourself with all aspects of the unit.
Like all mechanical products, this machine will require cleaning
and maintenance. Besides, dispenser working can be
compromised by operator's mistakes during disassembly and
cleaning. It is strongly recommended that personnel
responsible for the equipment's daily operations, disassembly,
cleaning, sanitizing and assembly, go through these
procedures in order to be properly trained and to make sure
that no misunderstandings exist.

3 INSTALLATION

1 - Remove the corrugate container and packing materials
12
HT10/1 HT10/1
HT11/1 HT11/1
HT 20/1 HT 20/1
n 1 2
l 10 10
11 11
20 20
cm 18 36
cm 47 47
HT 10 cm 62 62
HT 11 57 57
HT 20 69 69
HT 10 kg 20 26
HT 11 20 28
HT 20 22 32
HT 10 kg 22 29
HT 11 23 32
HT 20 25 35
n 1 2
and keep them for possible future use.
HT10/1 HT10/1
HT11/1 HT11/1
HT 20/1 HT 20/1
3 4
10 10
When handling the machine never grasp it by the bowls
11 11
or by the evaporator cylinders. The manufacturer
20 20
refuses all responsibilities for possible damages which
may occur through incorrect handling.
54 72
47 47
2 - Inspect the uncrated unit for any possible damage. If
damage is found, call the delivering carrier immediately to
62 62
file a claim.
57 57
69 69
3 - Install the unit on a counter top that will support the
combined weight of dispenser and product bearing in
34 41
m i n d w h a t i s s t a t e d i n t h e p r e c e d i n g p o i n t 1
36 44
42 55 IMPORTANT warning.
38 46
4 - A minimum of 15 cm (6") of free air space all around the
41 49
unit should be allowed to guarantee adequate ventilation.
46 59
5 - Ensure that the legs are screwed tightly into the base of
3 4
the machine.
Replace the standard legs originally installed with the 100
mm (4") legs whenever they are provided with the unit.
6 - Before plugging the unit in, check if the voltage is the same
as that indicated on the data plate. Plug the unit into a
grounded, protected single phase electrical supply
according to the applicable electrical codes and the
specifications of your machine. When the unit has no plug,
install a proper grounded plug, in compliance with
electrical codes in force in your area, suitable to at least
10 Amp 250 Volt (220-230 Volts 50-60 Hz areas) and
20 Amp 250 V olt ( 100- 115 V olts 50- 60 Hz ar eas)
applications. Should you prefer to connect the unit directly
to the mains, connect the supply cord to a 2-pole wall
breaker, whose contact opening is at least 3 mm. Do not
use extension cords.
Failure to provide proper electrical ground according to
applicable electrical codes could result in serious
shock hazard.
7 - Each drip tray has two diaphragm plugs: if a continuous
drain is needed, perforate one of the drain plugs and
connect it to a flexible drain line (see figure 1).
8 - The unit doesn't come presanitized from the factory.
B ef or e ser v in g p ro du c t s , t he d i s pe ns er m u s t be
disassembled, cleaned and sanitized according to this
h a n d b o o k
IMPORTANT
ATTENTION
figure 1
i n s t r u c t i o n s ( c h a p t e r
Ugolini S.p.A.