Elica ONICE 60 Gebrauchsanweisung Seite 11

INSTRUCTION ON MOUNTING AND USE
GB
Installation - Fig. 1-2
The cooker hood must be placed at a minimum distance of
50 cm from the cooking plane for electric cookers and 75cm
for gas or mixed cookers.
The hood is equipped with a top air outlet B for discharge of fumes
to the outside (Ducting version – exhaust pipe and pipe fixing
clamps not provided).
Should it not be possible to discharge cooking fumes and vapour to
the outside, the hood can be used in the filter version, fitting an
activated carbon filter, fumes and vapours are recycled.
Preliminary information for installation of the hood:
Disconnect the hood during electrical connection, by turning
the home mains switch off.
Expansion wall plugs are provided to secure the hood to
most types of walls/ceilings. However, a qualified technician
must verify suitability of the materials in accordance with the
type of wall/ceiling. The wall/ceiling must be strong enough
to take the weight of the hood.
Do not tile, grout or silicone this appliance to the wall.
Surface mounting only.
Remove the grease filter/s.
1 . Using a pencil, draw a line on the wall, extending up to
the ceiling, to mark the centre. This will facilitate
installation.
2. Rest the drilling template against the wall: the vertical centre line
printed on the drilling template must correspond to the centre
line drawn on the wall, and the bottom edge of the drilling
template must correspond to the bottom edge of the hood: bear
in mind that, when installation is complete, the underside of the
hood must be at least 50 cm above the cooker top in the case
of electric cookers, and at least 75 cm above the cooker top in
the case of gas or mixed cookers.
3. Rest the support bracket on the drilling template so that it
coincides with the dotted rectangle, mark the two outer holes
and drill them, remove the drilling template, insert 2 wall plugs
and fix the hood support bracket into place using two 5x45mm
screws.
4. Hang the hood on the bracket.
5. Adjust the distance of the hood from the wall.
6. Adjust the horizontal position of the hood.
7. Mark the 4 holes to be used for final fixing of the hood. Remove
the hood from the bracket.
8. Dril the holes (Ø8mm), insert 4 wall plugs. Insert 4 wall plugs.
Hook the hood onto the bottom bracket.
9. Fix the hood into its final position on the wall using 2 5x45mm
screws (ABSOLUTELY ESSENTIAL).
10. Connect a pipe (pipe and pipe clamps not provided, to be
purchased separately) for discharge of fumes to the connection
ring located over the suction motor unit.
If the hood is to be used in ducting version, the other end of the
pipe must be connected to a device expelling the fumes to the
outside. Make the electrical connections.
Consult the designs in the front pages referenced in the text by alphabet letters. Closely follow the instructions set out in this manual. All responsibility,
for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined.
11. Fix the bracket supporting the bottom section of the
chimney using 2 screws (one on each side – the bottom
bracket can be recognised because it is shorter than the
top bracket), rest the bottom section of the chimney over
the hood so that it covers the suction motor compartment.
12. After checking that the hood is perfectly positioned (see also
operations 4 and 5), use a pencil to mark the 2 holes used to fix
the bracket, remove the chimney, drill the holes (Ø 8 mm) and
insert 2 wall plugs.
13. Thread the top section of the chimney into the bottom
section, checking that the sides with the holes face
upwards.
Position the chimney sections over the hood once more, and
fasten the bottom section to the wall, through the bracket, using
2 screws.
14. Fix the top bracket on the vertical line of the bottom chimney
support bracket, close to the ceiling; using the bracket itself as
a boring template, use a pencil to mark two holes, drill them (Ø
8 mm), then insert two wall plugs.
15. Fix the top section of the chimney to the bracket using two
screws (one on each side).
16. Fix the bottom section of the chimney to the hood using
7 screws. Replace the protective internal screen.
Refit the grease filter/s and check that the hood is operating
correctly.
Electrical connection
The electrical tension must correspond to the tension noted on the
label placed inside the cooker hood. Connect the electrical plug,
where provided, to the an easily accessible outlet in conformity with
local standards in force.
Where an electrical plug is not provided (for direct connection to
electrical network) place a standards approved bipolar switch with
an aperture distance of not less than 3mm (accessible) from the
contacts.