Omron E5AR Gebrauchsanleitung Seite 4

Installation and Names of Parts
Installation dimension diagram (units: mm)
11.5
96
3
SUB1 SUB2 SUB3 SUB4
8.8.8.8.8
8
PV
8.8.8.8.8
SV
8.8.8.8
MV
OUT1 OUT2 OUT3 OUT4 STOP RSP
Panel work dimension diagram (units: mm)
92 +0.8
0
110 min.
I n s t a l l a t i o n p a n e l
thickness is 1 to 8 mm.
Do not mount in a
contact mounting
(observe the
installation gaps).
If installing multiple
units, make sure that the
ambient temperature of
the apparatus does not
exceed the temperature
specifications.
Names of front parts
Operation indicators
SUB1 SUB2 SUB3 SUB4
Channel display
8.8.8.8.8
8
Bar graph
8.8.8.8.8
Operation indicators
8.8.8.8
Function key 1
OUT1 OUT2 OUT3 OUT4 STOP RSP
Auto/Manual key
Function key 2 /
Channel key
Level key
5
E5AR
Terminal cover
110
(only included with -500 types)
95 1
(Model E53-COV14)
2
1
2
3
4
5
6
1
2
3
4
5
6
Crimp terminal size: M3
Installation procedure
(1) Watertight packing
(1) For a watertight (Model Y92S-P4)
installation, insert the
watertight packing.
Set the input type
setting switch on the
side of the Digital
Controller according to
the input type being
used.
(2) Insert the E5AR into
(3)
the mounting hole in
the panel.
(3) Insert the provided
fittings into the
mounting slots at the
top and the bottom of
the rear case.
(4) Tighten the top and the
(4)
bottom fitting screws
alternately little by little
(so that they remain
b a l a n c e d ) u n t i l t h e
ratchet stops engaging
when turning.
Names of rear parts (-DRT)
DeviceNet Connector
PV
Indicator 1
Indicator 2
SV
MV
Indicator 3
Up key
Down key
Mode key
Installation dimension diagram (units: mm)
48
1
SUB1 SUB2 SUB3 SUB4
2
8. 8 . 8 . 8 . 8
3
4
8. 8 . 8 . 8 . 8
5
8. 8 . 8 . 8
6
1
OUT1 OUT2 STOP RSP
2
3
4
5
6
Panel work dimension diagram (units: mm)
45 +0.6
0
60 min.
A R (2)
E 5
Names of front parts
Operation indicators
Mode key
Level key
Function key 1
Auto/Manual key
E5ER
Terminal cover (only included with -500 types)
110
11.5 95 1
3 2
PV
SV
MV
Installation procedure
(1) For a watertight
installation, insert the
watertight packing.
Set the input type setting
switch on the side of the
Digital Controller
according to the input
type being used.
Installation panel
(2) Insert the E5ER into the
thickness is 1 to 8 mm.
mounting hole in the panel.
Do not mount in a
(3) Insert the provided fittings
contact mounting
into the mounting slots at
(observe the
the top and the bottom of
installation gaps).
the rear case.
If installing multiple
units, make sure that the
(4) Tighten the top and the
ambient temperature of
b o t t o m f i t t i n g s c r e w s
the apparatus does not
alternately little by little (so
exceed the temperature
that they remain balanced)
specifications.
until the ratchet stops
engaging when turning.
Names of rear parts (-DRT)
SUB1 SUB2 SUB3 SUB4
8.8.8.8.8
DeviceNet Connector
PV Indicator 1
8.8.8.8.8
SV
Indicator 2
8.8.8.8
MV Indicator 3
OUT1 OUT2 STOP RSP
Down key
Up key
Function key 2 /
Channel key
(Model E53-COV15)
Crimp terminal size: M3
(1) Watertight packing
(Model Y92S-P5)
(2)
R
E 5E
(3)
(4)
6