Operation - sammic S-41 B Gebrauchsanweisung

neto-thermal switch of 40 A (2P). Cable 3x6
mm², 1.7 m long.
OPERATION OF THE ELECTRONIC CON-
TROLLER
Technical description of the control panel:
Figure A
MAIN SWITCH (1)
DISPLAY (2)
After powering up the machine
with main switch (1), the selec-
ted machine model appears on
the display for 2 seconds, immediately
followed by the tub temperature if the door
is closed (LED (a) on) or the boiler tempera-
ture if the door is open (LED (b) on). During
the cycle, the display shows the wash tank
temperature during the washing phase and
the boiler temperature during the rinsing
phase.
CYCLE TIME SELECTOR (3)
By pushing key (3) repeatedly,
you can select any of three
wash cycle times. Light indicators show the
selected cycle:
Glasswashers:
"d": Short cycle
"e": Medium cycle
"f": Short cycle ending in cold rin-
sing
Dishwashers:
"d": Short cycle
"e": Medium cycle
"f": Long cycle
Choosing the adequate cycle depends on
how soiled crockery is. The dirtier it is, the
longer the cycle has to be for an intensive,
thorough washing.
START CYCLE (4)
If you press this key, the wash
cycle starts and the associated
LED (g) turns on. At the end of the washing
phase, the rinsing process starts automati-
cally and this is shown by LED (h). Once rin-
sing has finished, the machine shifts to the
stand-by condition, with LEDs (g) and (h) flas-
hing. Flashing stops when the door is opened
or a new cycle starts.
On models with a drain pump, the machine
performs a draining cycle at the end of the
washing phase priot to rinsing. The asso-
ciated LED (j) will then turn on.
Press the key repeatedly to move from one
phase of the cycle to another. So, if was-
hing is on, press the key to shift to the rin-
sing process. During rinsing, press the key
to put the machine stand-by.
DRAIN (5)
This key works only if the
machine has a drain pump.
It has the desired effect only when the door
is open. Once pushed (LED (j) on), the drai-
ning cycle starts. By pushing the key again,
the draining cycle stops.
Upon completion of the draining process,
filling will start again, unless the user has
powered the machine down by turning
main switch off.

OPERATION

Start-up
1.Open the 3/4" stopcock to allow water to
enter the machine.
2. Turn on the magnetothermal switch that
protects the installation.
3. Check that the filters and the drain plug
are in place, as Figure "C" shows.
4. Turn the main switch (Fig. A-1) to the ON
position for the automatic filling of the
wash tank and the connection of the
heater elements.
5. The light indicator (Fig.A-c) turns on
when the washing temperature (55º/
60ºC) has been reached.
6. Start Cycle:
- Place the objects to be washed in a
basket (rack).
- Close the door.
- Select the washing programme by
pressing the button (Fig. A-3) accor-
ding to the soiling level. The associa-
ted red LED will turn on.
- Press the Start Cycle key (Fig. A-4). The
washing phase indicator light (Fig. A-g)
turns on. The machine completes the enti-
re washing cycle. If you press the Start
Cycle key (Fig. A-4) again during the was-
hing phase, the programme immediately
shifts to the rinsing process. Pressing the
said key during the rinsing phase causes
the machine to stop.
On models "B" with a drain pump, the
machine performs a draining cycle at
the end of the washing phase priot to
rinsing. The associated LED (j) will then
turn on.
7. When the complete cycle has finished,
the two indicators (Fig. A-g) and (Fig. A-
h) flash.
8. Models with a drain pump: With the door
open, press key (Fig. A-5) to start the
drain pump for a given period of time,
which is long enough to empty the tub.
At the end of this time, the pump stops.
Press the "Drain" key (Fig. A-5) to alter-
nately start and stop the pump. With the
drain plug, any residual water will be
removed from the tub.
Detergent dispenser
The glasswasher is prepared for its fitting
with an adjustable detergent dispenser, the
part number of which appears on the spare
parts list. This dispenser has to be installed
in the machine base, at the front, as shown
on the exploded view. At the rear of the
wash tank, there is an opening where to
insert the detergent injection nozzle.
The dispenser delivers about 0.7ml/s of
detergent (maximum). At the first filling of
the tank, feeding of detergent is roughly
119ml in 170s, resulting in a maximum con-
centration of 3ml/l. At each cycle, the dis-
penser delivers 10ml of detergent. It is pos-
sible to reduce or increase the injected quan-
tity by turning the adjusting screw on the dis-
penser.
NOTICE : The manufacturer shall assume no
responsibility for defects due to incorrect
electrical connections of the dispensers.
Rinsing aid dispenser
Verify that the rinsing aid reservoir is full.
Start and stop the washing water pump 5 or
6 times by pressing "Start Cycle" (Fig. A-4)
and check whether the tube fills up with
rinsing aid and goes in the boiler. Setting
the dispenser is done by turning an adjus-
ting screw on the front lower panel in the
direction shown on the panel graph.
In order to determine whether the amount
of rinsing aid is adequate, look at the glas-
ses against the light. If there are water dro-
plets on the glass, the amount of rinsing
aid is insufficient; if streaks develop, the
quantity of rinsing aid is too much.
Machine Draining
Models with no drain pump: Open the door
and take out the drain plug, leaving the fil-
ters in place. Water will fall by gravity, dirt
accumulating in the filters.
Models "B" fitted with a drain pump:
· Open the door and take out the drain
plug, leaving the filters in place.
· Press the drain key (Fig. A-5) as specified
on the control panel, with the door open.
The drain pump operates during the pro-
grammed time at the end of which it
stops automatically. By pressing the key,
you can successively start and stop the
pump.
· Put the overflow drain plug and filters in
place again.
· Turn the main switch off and close the
door.
Water softener. Setting water hardness.
You need to set the water hardness value
on the electronic board. The machine sig-
EN 7